posted
Has anybody done this to a Bear Mag handle? Bought one for my wife, and it desperately needs a new paint job, so its either Powdercoat or Spray Paint, not sure which one yet. I think the PC would be a tougher finish but not sure about baking the riser to complete the job. Spraying it would be easier, and cheaper, but I want it to be something that looks professional and is tough. What to do?
The limb pockets have rubber buttons in them, can these be popped out and then just popped back in?
Thanks, Tim.
-------------------- USMC 1992-2000 PBS Associate Member Comptons Traditional Bowhunters Member Bowhunters of South Carolina-County Rep (Dorchester) Posts: 1645 | From: South Carolina | Registered: Feb 2005
| IP: Logged |
posted
Tim; Contact Rich Lopez. His site is http://www.droptinetraditions.com/php/ and follow the links to his refinishing service. I know he specializes in restoring Mag handles but I don't know about powder coat. Of course bowdoc also does excellent restoration/refinishing work and you might check with him too. I do not know if he does powdercoat either, but you can check bowdocsarchery@comcast.net.
Good luck
Al (Als Decals)
Posts: 179 | From: Campbell, CA | Registered: Mar 2007
| IP: Logged |
posted
Thanks Al, maybe one of them will chime in here, if not I'll shoot each of them an email. Tim
-------------------- USMC 1992-2000 PBS Associate Member Comptons Traditional Bowhunters Member Bowhunters of South Carolina-County Rep (Dorchester) Posts: 1645 | From: South Carolina | Registered: Feb 2005
| IP: Logged |
posted
Hi Tim your right.The powder coat is about 10 times stronger then most paints.I think powder coating is the best...Originaly they were powder coated at the factory.I can't remember which,but one of the Fred Bear videos shows the risers being coated and baked in an oven...bowdoc
Posts: 7927 | From: Seattle Wa. | Registered: Dec 2004
| IP: Logged |
posted
I'm sure Rich may chime in, but I know he is tending to something very important that may keep him away from the net for a bit.
If you powder coat anything, just seal the threads, and be careful chamfering any edges.
I have thought about it before with a riser, but wondered if it was cost effective. No doubt you could get some WILD results.
Posts: 2199 | From: Eldersburg, MD | Registered: Dec 2006
| IP: Logged |
posted
Raghorn has done several,, He's busy these days and may not get on,,, but yes it works great if you are hooked up with a knowledgeable coater with good color options.. Make sure and open all holes before it cures.
-------------------- Many have died for my freedom. One has died for my soul. Posts: 1962 | From: Nebraska | Registered: Apr 2003
| IP: Logged |
posted
I saw on Riches website that he does his with Aircraft epoxy paint, the pic of the one he did looked great and almost identical to powdercoating. I guess it depends on whether he can get the color that my wife wants; PINK.
-------------------- USMC 1992-2000 PBS Associate Member Comptons Traditional Bowhunters Member Bowhunters of South Carolina-County Rep (Dorchester) Posts: 1645 | From: South Carolina | Registered: Feb 2005
| IP: Logged |
posted
Tim darned if I can find the video of Bear Archery powder coating the mag risers.maybe one of these other guy's remembers which video it is.bowdoc
Posts: 7927 | From: Seattle Wa. | Registered: Dec 2004
| IP: Logged |
posted
It is "Rural ?Road ?Route One" - but them are 1976's or Bearcat T/D risers which are coated ...
Posts: 980 | From: Lower Saxony, Germany | Registered: Jan 2004
| IP: Logged |
posted
I have had several powder coated locally here in Denver. Lots of different colors and textures to chose from. Some I had cleaned up myself and others I had them sand blasted. Be careful and explain to the company that the limb pockets are sensitive areas and the metal is thin. Blasting can remove too much metal and the powder needs to be applied thinner in this area. Make sure the all holes are plugged or they are cleaned out immediately after spraying. Removing the pin that retains the latch hook can be tricky.
Powder coating is the most durable and proper way to do anything metal. However, baked on Imron epoxy (aircraft paint) is just as durable a if not rock solid if applied correctly with proper equipment for a riser.
Most industrial outfits sell do it yourself powder coating kits, but they suck. To do it right, it will take an investment of $500-1000, and lots of room with correct atmosphereic conditions. Further, it is messy.
-------------------- TGMM Family of the Bow Posts: 2499 | From: baltimore, md. | Registered: Mar 2004
| IP: Logged |
posted
Tim- I have been powder coating for about 30 years now. I'll shoot it for you just to say I did one as long as it's one of my stock colors. Don't worry about the masking. We do it every day. Mark
Posts: 34 | From: Lake Village, Indiana | Registered: Jan 2008
| IP: Logged |
I've had two done and plan on getting another one or two done at some point.
Stay away form gloss colors. They look cool, but on a porous material like cast magnesium they show every little flaw. My flat black one is awesome. All of the pieces come off easily. The guy that did mine had nylon plugs for all the holes.
There's a ton of colors but to keep costs down you need to see what yuour guy has in stock. Since the guy I deal with does mostly car stuff the "natural tones" were few and far between.
Here's the gloss "black jade" cool color wish it would have worked better. Don't have pics of the black one.
UBBFriend: Email this page to someone!
Printer-friendly view of this topic
![[Roll Eyes]](rolleyes.gif)
