Trad Gang

Main Boards => PowWow => Topic started by: Autumnarcher on April 04, 2009, 09:51:00 PM

Title: Hexpines Fresh Out Of The Shop
Post by: Autumnarcher on April 04, 2009, 09:51:00 PM

Just thought I'd share a pic of my latest creation. Hexpine shafts, Four 4" feathers,and some decal work. Finish is 2 coats Minwax stain, 1 coat oil poly, crest, then another coat water-based poly, 1 coat oil poly, and 1 coat gasket laquer. Sand each coat with 220 grit and then a few swipes of steel wool. Finished at 28" BOP, 125 tip tips the scales at 576 gr.

 (http://img.photobucket.com/albums/v284/autumnarcher/009.jpg)

 (http://img.photobucket.com/albums/v284/autumnarcher/003.jpg)

Title: Re: Hexpines Fresh Out Of The Shop
Post by: beachbowhunter on April 04, 2009, 10:02:00 PM

Yikes, you sure have raised the bar! Those are beautiful.

Title: Re: Hexpines Fresh Out Of The Shop
Post by: Autumnarcher on April 04, 2009, 10:19:00 PM

I've had a lot of people ask me how I do the decals. I use waterslide decal paper, Not sure where I got it, google it and you can find it easy enough. The I just use Microsoft Word or any other similar program to type the lettering in whatever font I want to use. For the pics, such as my little Scottish Longbowman, I just paste the .jpg and resize it until I get one that fits on an arrow. The print it on your computer printer.

I originally got this through Tester's, the plastic model company. Its the same paper as the decals that go on their model cars. They also sell this spray that seals the printer ink. To apply the decals, after the sealer dries, you just cut them out and soak 'em in water for about 15-20 seconds, and slide them off onto the arrow. The sealer is necessary to keep the water from making the inkjet ink run.

Smooth the decals out with a fingertip to get any trapped air out, and after they dry, I seal 'em in with a coat of water based poly. I think oil would work too,but it tends to be a little yellow, whereas the water based dries real clear.

You are limited only by your imagination and  computer savvy as to what you can print and apply to arrows. Once done, you can't tell its a decal at all. I found keeping the decals small is easier to get them into the position you want.

Title: Re: Hexpines Fresh Out Of The Shop
Post by: J. Adams on April 05, 2009, 12:42:00 AM

:thumbsup:    :thumbsup:    :thumbsup:

Title: Re: Hexpines Fresh Out Of The Shop
Post by: frank bullitt on April 05, 2009, 10:31:00 AM

John, those are beauties! Thanks for the info on the decal, it gives me some ideas to work with! I'm still trying to figure out this computer stuff.

Title: Re: Hexpines Fresh Out Of The Shop
Post by: Tom Phillips on April 05, 2009, 10:34:00 AM

THose are nifty.   Nice work.

Title: Re: Hexpines Fresh Out Of The Shop
Post by: flint kemper on April 05, 2009, 10:56:00 AM

Very nice indeed. Thanks for sharing Flint

Title: Re: Hexpines Fresh Out Of The Shop
Post by: Autumnarcher on April 05, 2009, 12:18:00 PM

Here is a link to one supplier of the waterslide decal paper.

  http://www.decalpaper.com/category-s/2.htm  

Also, for the sealer spray, Krylon or any other acrylic clear coat spray will work.