Trad Gang
Main Boards => PowWow => Topic started by: Marvin M. on October 22, 2009, 03:24:00 PM
-
I've seen posts about this before, but never thought I'd be part of it. Safety is always something that I'm conscious of, but it still got me today.
Four or five years ago, I bought a bow stringer on the St. Jude's auction. I won't mention who it was because this wasn't his fault and I don't want to cause any problems for him. It's been great, but it wore out. First, the cup end broke, and I rigged up something to take it's place. Then, a couple of weeks ago, the tip end broke. I tried to replace that, but initial attempts didn't work for me -- too big and they slid into the string groove so I couldn't get the string in. Yesterday I found the old piece that was originally on there, and cut a piece of leather to match it, and put it on the string.
I went out at lunch and was going to shoot a little. Well, the leather cup broke, under full tension with me leaning over to slide the string on. The upper limb smacked me in the head.
My first thought was, "Wow, that hurt", and next was "Hey, where's all this blood coming from?".
I grabbed my handkerchief and applied it to my bleeding eyebrow, and went to the mirror on my Ford. "Wow, there's blood everywhere". I got into my vehicle and drove back to the office to see if someone would take me to the ER. I got to the bathroom, cleaned up the would and decided that an ER wasn't necessary, but I should definitely got the an Urgent Treatment Center for stitches.
I lost count at five stitches through my eyebrow just about centering my eye. I was wearing my glasses at the time, but they weren't damaged. Got a little scratch on the bridge of my nose where they were pressed into me -- minor compared to the gash the bow limb put into me.
I was lucky!!! Five to seven stitche, still not sure how many they put in. A mild headache, and some embarassment at the whole situation. It could have been a lot worse.
BE CAREFUL WITH BOW STRINGERS!!!!
-
OK, now that I got that out of the way, I've got to come up with a way to string this bow.
This is a Bingham's Projects Take-Down Longbow that I made. Shoots great when I can get it strung.
I bought two bow stringers last week that won't work with it. It's a hybrid design and regular stringers won't work. I bought a "universal stringer" and a longbow stringer that is supposed to work for any longbow. I guess they would if I was eight feet tall and could pull like a draft horse. The curve on the tips is such that the string lays way back and these two stringers have the kind of end that sits on the limb behind the string and pulls from there. I can't get them any closer to the tips where they need to be to get enough leverage to pull the tip down to meet the string.
I tried the step through method and again, I'm not strong enough to do it. Call me a "girly man" if you want, but right now I've got a sore head, stitches, and a bow I can't get a string on.
Any suggestions?
And, I had a friend take a picture, but not sure I should post it here. Nice little gash that turned my eyebrow into a plus sign.
Thanks for any suggestions.
Marvin
-
WOW!!! glad your okay, it could have been a lot worse!!! to me stringing my bow is the scariest part of the whole shooting process. most of my bows the stringer works fine but the Kiowa I just got has very short limb tips and my stringer gets in the way of the string getting into the grooves, keeps me on my toes for sure!
-
Sorry to heaer about your misfortune. Instead of trying to step thru, which to my understanding would be effective on a recurve, try a push-pull. Place your bottom tip down in the arch of your foot, then while pulling the riser push the upper limb tip while sliding the string up to its nock groove. This is how I always string my longbows.
-
:scared: Sorry to hear about your mishap!!! Hate stringing my bows had my 60# Brack 'slip out' of the stringer on me! I only shoot longbows now and I can recommend the Web-ster Stringer that A&H sells. The CX is quite a deflex limbed bow and I have had no trouble with it! Well at least you've got a good war wound to tell the kids about! It could have been a lot worse! :eek:
-
The best and safest is still a bow stringer, buy the best one you can and keep an eye on it. Stuff don't last forever. Replace it when it looks questionable!
-
Well, actually bowstringers aren't dangerous...people are 8^). The first issue was trying to fix a bowstringer via home remedy. :knothead: I have several laying around and will gladly give you one. They aren't that expensive really, and if they look worn, they should go in the trash bin....not be repaired.
Glad you're okay. Now on the inside of your upper limb, write "Stitches" in white marker 8^).
It will let you remember.
-
you have a PM
-
Sorry to hear about the accident and glad you are Okay.
I think old, worn out bowstringers are dangerous too.
Joshua
-
Well said George. :banghead:
-
sorry to hear about ya eye. now if i were you i would use the step through style a lot safer allround :thumbsup:
-
Another great reason to leave the bow strung and just shoot it daily. Glad you aren't injured any worse.
-
George said what I wanted to say.
Guy
-
Originally posted by HO'NEHE JEFF:
sorry to hear about ya eye. now if i were you i would use the step through style a lot safer allround :thumbsup:
Step-through method will possibly twist or misalign the limbs though, if not done correctly.
-
if your new stringer is too long just tie a few knots in the string center...do this until you get the length you want.
-
I'm with sou-paw. If you're using a longbow and NOT a recurve, use the push pull. If that is too hard to do I respectfully suggest that you have too much bow weight.
Stingers for the recurves. Don't use the step though method on either of the types of bows. That's how you twist limbs -- at least one of the ways.
-
My wife's' uncle died from trying to use the step thru method. The bow slipped and hit him around the eye socket breaking the bone and driving it into his brain. Bow stringers are about the safest way to go. IMHO
God bless,Mudd
-
If the string is too long, step on it with both feet, shoulder width apart, then lift
ChuckC
-
Originally posted by Mudd:
My wife's' uncle died from trying to use the step thru method. The bow slipped and hit him around the eye socket breaking the bone and driving it into his brain. Bow stringers are about the safest way to go. IMHO
God bless,Mudd
GOOD LORD! :scared: Seriously? That's a very sad story.
-
If the stringer is too long just spread your feet apart further. You'll be pulling the bow with more power too. Don't use old, worn stringers!
-
Got popped above my right eye with boo backed hickory longbowbow when it slipped out of the cup. I never saw it even move. It was almost strung so the limb had LOT of energy. I bled like crazy! It would have DESTROYED my eye had it hit there instead.
-
I swear by the Selway stringer, it works on recurves and longbows. Probably the safest and long lasting stringer out there.
-
Glad your OK :knothead:
-
Mudd, A tragedy to be sure. However I think we have a definition problem. With the "step through" method the bow is behind the leg and any release of the bow limb would shoot the limb down and away from the body. The push pull method could cause this type of accident if the individual was unaware of the danger. I do agree that Stringers are the safest way overall but agreeing with many of the above responses the safty issue is largely an individual responsiblity to know how to do it right.
-
About the Selway stringer- I can't use one. It takes about twice the pressure of a normal stringer to even get the limbs to start to bend. What am I doing wrong? I tried it on 58, 60, 62 and 64 inch bows.
Joe
-
Maybe I just have to make the stringer longer. It seems the rubber block is too far down on the upper limb.
Joe
-
Glad you're OK. I had a stringer cord break on me years ago while stringing up a 60# recurve. The upper limb took me right across the nose. Believe me, that'll cross your eyes! It just taught me to keep my face a little farther from the bow when stringing it. The stringer is still the best way to go. Be safe.
-
Frisky, slide the block up right against the loop making sure all the slack is out of the bow string and then start to pull up on the bow slowly. Slide both the block and loop up the limb at the same time as it starts to bend. The block will move up a little higher then stop and you just keep on pulling as you slide the string up on the nock. If you do it this way you can get the block closer to the tip which makes it easier to string.
-
Thanks Molson. I've have to work at using the Selway, as I've had it sitting around for 5 years unused. My bows string nearly effortlessly with my traditional cup stringer. The Selway, even stringing a 45# bow, is a back breaker!
Joe
-
Wow! Sounds painful.
I'll be the first one to ask I guess.... how about those pictures????? (Yea, I rubberneck wrecks on the highway too...)
I've tried stringers too and never liked them I feel safer, and more in control with the push pull method but I take care to note the "line of fire" and turn my head. There is one other method for stringing a longbow though that works great especially if you have to fight the bow hard under normal stringing.
Put your back to a wall and put the bottom limb tip against the floor and wall. Lean the bow out away from you and hold it just below the string loop on the top limb. Put a toe of one foot on the lower limb up near the fades and put the knee of the same leg against the upper part of the bow. While pulling the top limb with your hand, slightly slide your back down the wall and let it put pressure on your toes and knee where they contact the bow. Might have to push a little with your foot but it's a real easy to flex the bow and it's all directed away from you. When you bend the limbs enough, slide the loop up into place and ease off the tension.
One thing I always do is to turn my head away a bit and I also turn the bow to horizontal with the string to my legs immediately after stringing (by any method). Once the bow is turned this way, it's safe to look directly at it and ensure the string is in the groove ON BOTH ENDS.
I once strung a recurve and while the top loop went into the nocks nicely, the bottom loop evidently came partially out. I turned the bow to inspect the top loop and BAM! It unstrung and the top tip came back and knocked a hole in my chin that made me look like Kirk Douglas for a couple days. Lucky it wasn't my eye on that one.
-
I never had the bow slip with the push-pull. What I have done though, is having the loop somehow "missed" the nocks, so the loop slided down the upper limb and pinched my index finger so hard that all I could do was to slowly slide my finger all the way down the limb, while it being squeezed really, really hard by the string. The pain was extreme, and my finger was all bruised and swollen from the pinch.
-
I have used two selways stringers now for years. Never had a problem, never had it slip, never had it pop off the tip. I like them because they really cover the entire bow tip; which feels more secure to me. BTW, I use it on recurves and longbows.
But I can tell you I really dont like stringing and un stringing my bows. I have read too many stories like this one. So, I am very aware of everything when stringing a bow.
And I agree with George, its not worth trying to repair a stringer, and you probably will never do that that again.
Sorry to hear of your accident and I hope you heal up well.....glad it didnt cause any permantly damage.
-
The wife's uncle was definitely using the step thru method. His grandkids were visiting and had found an older recurve down in the basement. Naturally they wanted to have fun with the bow. They couldn't find any arrows so grandpa took them to town, bought some arrows. They all hurried home to shoot the bow. Being inexperienced with bows,he was struggling with it causing him to bend/lean over the bow and move his head close to and over the backside of the upper limb. The whole thing was an avoidable tragedy. The fact that the grandkids were standing right there made it all the worse.
-
OK, I'll post a couple of pics in the interest of education. Mods, if these are too graphic, let me know and take them off. Don't want to offend anyone or scare small children, but this is probably something that people should see.
Here is the before shot. This is 20 minutes after it happened and just after I got the bleeding stopped and did some preliminary cleanup. Swelling hadn't really started yet.
(http://img.photobucket.com/albums/v102/kyarcher76/ImportedPhotos00006.jpg)
And this one is this morning. Eighteen plus hours after and with the stitches. Can't really see the nice purple color of the eyelid in the photo, but you get the idea.
(http://img.photobucket.com/albums/v102/kyarcher76/ImportedPhotos00007.jpg)
Good comments from everyone. I'll respond in a few minutes.
-
OK, so good info presented here. Might help someone else avoid this thing in the future.
Dave, I may have to try that wall method. Sounds promising and less dangerous.
George, I like that idea on keeping score. This bow has been blooded, but it's all mine to this point. First laminated bow I've made and I want it in the woods.
A little about the bow. Bingham's Project made from their plans. Radical Take-Down Longbow (68 inches) with limbs to make a 55 pound finished product. I never put it on the scales to see what it actually came in at, but it's heavier than my 50 pounder, and shoots the same arrows.
I think I'm going to name it "Tyson" since it looks like I got clocked with a good left.
What I'm trying to say here is that it isn't the length of the stringer, it's the design of the bow.
I didn't want to talk brands on the stringers, but since several of you brought this up, I'll comment. I knew I had problems with the old stringer. I bought two from Three Rivers last week. One was the Selway Longbow stringer. The curve in the limbs is such that when I put the stringer behind the string, it is a pretty long distance from the tip, and the part of the limb that is bending is a lot stiffer than the tip. If I could get it closer to the tip it wouldn't be a problem. I can't slide the rubber tip up behind the string since there is a lot of pressure on it once it starts bending.
The other stringer I bought was the Universal Stringer from Three Rivers. Same problem. Placing it behind the string doesn't allow enough pressure on the tip.
I'm not bashing either of the above stringers. I think they are good quality and would be great. But this bow is hard to string and this design isn't good for this bow!!!
I went back to the old stringer and tried to repair it because I couldn't get either of the two new ones to work. My leather wasn't strong enough. The failure was in the leather cuff that I made. I needed better leather.
-
I use push-pull on all bows (curve and long). Never had a problem- and I never look down either! If done carefully I can not see how it can twist a limb. The same pressure points as a stringer but with better control/feel for me. After it is strung you immediately turn it the other way. . .then check it.
-
that sucks. i hope i dont have that same issue. gald to see you didnt hit your eye
-
Have you tried using two feet on the stringer at shoulder width or more, making a "trapeziod" shape? That puts the pull out on the tips....
something that works for me on longer bow (68").
You might need to have the cord longer to do this (though I haven't).
BobW
-
Marvin, that's about the same sort of trouble I had when using a stringer with the rubber slide block. It was a real bugger to slide that block on the limb when I had pressure on it. I'm a pretty good sized guy and it was a strain. Plus I was always afraid of a tip popping out of the stringer pocket.
I just feel more comfortable using the push pull. If you can draw your bow easily, the push pull is even easier as you only "draw" it to brace height. It's like any other mildly dangerous activity, there are certain precautions you have to take when doing it. Done properly, you should never have a problem. Kinda like hunting in general. I trust my hands and arms not to fail without giving me ample warning. I can't say the same for a bow stringer.
-
BobW,
Always shoulder width or wider. I'm reaching well below my knees when I start. Lenght isn't a problem.
And I freely admit I'm not the strongest guy out there, but I had no problem stringing this bow with the stringer I started with.
The design of the bow makes it hard to use a stringer that you have to set behind the string. Once pressure is on that rubber piece, it doesn't slide easily, if at all. It needs to be on the tips. But the one I had (and repaired) failed. I think the leather I used was dried out and had no "give" to it.
-
Just a few months ago I was using a rubber block stringer and the stringer cut right through the block and let go of the bow. Very exciting.
I now use stepthrough and make sure the limbs are aligned throughout the process.
-
That is almost exactly where mine was!! I don't think some one could swing a stick as fast or hard as a long bow moves when loosed!
-
I've heard of a woman that put her eye out while stringing a recurve. I don't remember what method she was using.
I sure give a bow alot of respect and attention when I'm stringing them up. I keep my fiberglass bows strung.
Marvin, that looks painful. I'm glad you will be ok.
Bona
-
Marvin, COOL pics...now your face has some character! Just think of the cool stories you can tell your grandkids!
Bowstringers make me nervous. I always keep my hand between the limb and my face. I can handle a broken finger but my face has enough character already!!
-
What does the other guy look like OUCH! :bigsmyl: :wavey: :coffee: :goldtooth: