3Rivers Archery




The Trad Gang Digital Market














Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters




RIGHT HAND BOWS CLASSIFIEDS

LEFT HAND BOWS CLASSIFIEDS

TRAD GANG CLASSIFIEDS ACCESS


The "hole" truth, and nuthin' but the truth!

Started by Captain*Kirk, June 30, 2016, 10:58:00 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Captain*Kirk

Last fall I purchased a used Bear Kodiak Magnum  with a sight attached. For snicks and grins, I tried shooting it with the sight on, but the pins were way off for my shooting style.







Well, I've decided to remove it, and I'm wondering what would work to fill the two screw holes drilled in the riser.
Epoxy? Fiberglass resin? Glue?
I don't want to make a mess of it, and on the off-chance I might want to remount the sight some day (who knows, it might snow in hell some day), don't want anything too ultra-permanent.
But I don't want holes in the riser, either...
Suggestions?
Aim small,miss small

Longtoke

many use sawdust mixed with superglue,  riser inserts might also be an option

Pine

I would just leave the holes , there not going to get any worse .
Then someday if you are sure that your not going to remount the site , then fill them .
It's easier to fool someone than to convince them they have been fooled. Mark Twain

If you're afraid to offend, you can't be honest.

TGMM Family of the Bow

Pine

I would just leave the holes , there not going to get any worse .
Then someday if you are sure that your not going to remount the site , then fill them .
It's easier to fool someone than to convince them they have been fooled. Mark Twain

If you're afraid to offend, you can't be honest.

TGMM Family of the Bow

Shadowhnter

If I was in your frame of mind, Id probably just put the screws back in the holes and snug them down. If they are too long, id by a set of shorter ones.

Kip

Take a file or sandpaper to some white  PVC pipe and get about enough shavings to fill the holes with clear glue and the shavings I did one and came out good. The green top hole try to find something plastic to do the same. Kip

Captain*Kirk

QuoteOriginally posted by Kip:
Take a file or sandpaper to some white  PVC pipe and get about enough shavings to fill the holes with clear glue and the shavings I did one and came out good. The green top hole try to find something plastic to do the same. Kip
I was considering Elmer's glue with shavings. Sounds do-able.
Aim small,miss small

MCNSC

They make an epoxy for repairing small scratches and dings on white fiberglass boats. I used some one time, it was kinda pricey but did a good job on the boat, seems it was around $25 for a few oz bottle and the hardener ,always thought it would work great for holes in bows.
I have also added dye to epoxy to make it black, if they make a white dye l bet it would work too.
"What was big was not the trout, but the chance. What was full was not my creel, but my memory"
Aldo Leopold

"It hasn't worked right since I fixed it" My friend Ken talking about his lawn mower

ron w

For now just take the pins off and leave the base.
In the beginner's mind there are many possibilities. In the expert's there are few...So the most difficult thing is always to keep your beginner's mind...This is also the real secret of the arts: always be a beginner.  Shunryu Suzuki

Captain*Kirk

QuoteOriginally posted by ron w:
For now just take the pins off and leave the base.
Already removed the sight, Ron.
The PO used wood screws instead of inserts, left the holes sort of a mess.
In the end,I guess it's all cosmetic but I hate to see a nice bow mucked up.
Aim small,miss small

Mix a little white paint in epoxy; fill the holes and let it dry. Sand down and spray with satin urathane.  You can do the same with the green but the color match may be a bit more difficult.


Contact Us | Trad Gang.com © | User Agreement
Copyright 2003 thru 2025 ~ Trad Gang.com ©