Author Topic: Big Problem!!!!--Help (Read 840 times)

MW · « **on:** January 13, 2008, 05:46:00 PM »

I was in the garage shooting. And while walking up to the target looked at my bow. I tried to get some pictures but these are the best I could get.

In atleast three places the finish is discolored and there are large cracks running across the bow.

They are all on the bottom limb about half way.

The bow is stored at room temp (63) and the garage is about 50.

What do I do?

Kingstaken · « **Reply #1 on:** January 13, 2008, 05:51:00 PM »

If thats snake skin, lQQks like soemthing been eating the skin.

hormoan · « **Reply #2 on:** January 13, 2008, 05:53:00 PM »

Looks like moisture under the finish Mitch. I see it a lot on poly type finish's on firearms. No sure about a cure other than a refinish. Hopefully bow doc, or droptine will chime in. Are they snakeskins applied?

Brent

MW · « **Reply #3 on:** January 13, 2008, 05:57:00 PM »

Brent,

I don't understand the question?

Mitch

MW · « **Reply #4 on:** January 13, 2008, 05:59:00 PM »

I don't think its moisture as it is in there different spots inches apart.

Bob Morrison · « **Reply #5 on:** January 13, 2008, 06:01:00 PM »

Take some more pictures we can see.

ratgunner · « **Reply #6 on:** January 13, 2008, 06:03:00 PM »

Yeah,better pics would help.I'm betting it's just something in the snakeskin backing and nothing major.

MW · « **Reply #7 on:** January 13, 2008, 06:03:00 PM »

Ill try.

hormoan · « **Reply #8 on:** January 13, 2008, 06:09:00 PM »

The pictures are pretty fuzzy, it looks like you have snakeskins on the limbs. A lot of guys spray or brush a poly finish over them. And cracks like those shown in the pictures allow moisture to get under the finish. It always turns a milky white color under it. It only looks bad won't hurt otherwise, granted thats the case.

MW · « **Reply #9 on:** January 13, 2008, 06:17:00 PM »

It looks like there are some cracks in the finish. Where these have occured it creates an off colored spot. The cracks dont seem to go into the snake skin.

MW · « **Reply #10 on:** January 13, 2008, 06:18:00 PM »

Sorry about the pic. I can't seem to get good ones.

Crooked Stic · « **Reply #11 on:** January 13, 2008, 06:25:00 PM »

Appears to be a finish problem. No expert here but you may have redo the skins.

steadman · « **Reply #12 on:** January 13, 2008, 06:40:00 PM »

Bummer Mitch. I think it's a finish problem as well. Looks like a bubble under the finish. Someone else might know how to fix it. Sorry I don't.

snapper1d · « **Reply #13 on:** January 13, 2008, 06:42:00 PM »

There was too much finish on it.The finish comes loose from the skin after shooting a lot.The skin not being solid like wood or glass and it comes loose and it cracks like that.You would have to strip it all off and start over.I know thats not what you want to hear but the finish is still stuck to parts of the skin and there is no way to separate it from the skin with out messing it up.When the skin deteriorates even slightly the finish can start to come loose.The finish being loose from the bow while flexing is what causes it ti get the cracks also.When finishing skins you dont need a lot of finish on them like that because thats what can happen.I have seen it happen several times.

Bob Morrison · « **Reply #14 on:** January 13, 2008, 07:01:00 PM »

The finish is coming loose from the skins, Possible the type finish you used... They can be stripped with paint remover and a brush, you'll probably end up refinishing the whole bow. Take it slow or you will end up replacing the skins too. use Thunderbird finish, the 1st coat very thin.

snakewood3 · « **Reply #15 on:** January 13, 2008, 07:24:00 PM »

Thunderbird was the finish used on that bow, and yes the first coat was very thin. I think the problem could be the finish thickness causing it to delam from the skins. Your PM box is full. Send me the bow and I'll refinish or reskin it ...whatever it takes.

Keefer · « **Reply #16 on:** January 13, 2008, 07:40:00 PM »

I thought that thing was gettin ready to shed

steadman · « **Reply #17 on:** January 13, 2008, 09:22:00 PM »

There ya go Mitch! Outstanding snakewood! This just gives you a bigger kick in the butt to make you a longbow or two :D

tippit · « **Reply #18 on:** January 13, 2008, 09:30:00 PM »

If anyone can fix it right, it would be snakewood3...Doc

MW · « **Reply #19 on:** January 14, 2008, 11:49:00 AM »

Thanks for the info.


LEFT HAND BOWS CLASSIFIEDS	TRAD GANG CLASSIFIEDS ACCESS	RIGHT HAND BOWS CLASSIFIEDS

News:

Author Topic: Big Problem!!!!--Help (Read 840 times)

Users currently browsing this topic: