Author Topic: Primitive Friction Folder, with a question (Read 857 times)

Steve Nuckels · « **on:** February 07, 2012, 03:05:00 PM »

My first folder so far.

Stock removal from an old sawmill blade. Clay backed and etched. File work on the tang and on the whitetail antler crown.

Learned alot from this project, most important lesson is pick the antler, then design the blade, that will save a headache or two!

And I made the tang too long! It was fun!

Been considering a sheath design while I find some rawhide!

Steve
---------
Potomac Forge
ABS Apprentice

JohnHV · « **Reply #1 on:** February 07, 2012, 04:01:00 PM »

Steve,

That is pretty slick!

I've tried to do something similar in the past and had a little difficulty keeping the cut for the slot in the antler straight.

Would you mind sharing how you cut yours?

snakewood3 · « **Reply #2 on:** February 07, 2012, 04:08:00 PM »

That's a sweet one Steve. PM me if you need some rawhide.

4est trekker · « **Reply #3 on:** February 07, 2012, 04:51:00 PM »

Yeah, buddy!

That's a looker for sure

Scott Teaschner · « **Reply #4 on:** February 07, 2012, 05:28:00 PM »

Very Cool Steve!

oldpaths · « **Reply #5 on:** February 07, 2012, 05:40:00 PM »

Nice one bro.,I like the little sticker point left on like that.

kansas stik man · « **Reply #6 on:** February 07, 2012, 06:45:00 PM »

great work , how do you shape the white part ?

Steve Nuckels · « **Reply #7 on:** February 07, 2012, 07:41:00 PM »

John, I must confess cutting the slot where I pinned the blade and the slot on either side for the blade and the tang was difficult! The antler pictured was my second try!

I used a straight edge and eyeballed it for the most part. I made two cuts with my band saw then used a variety of files. A good tip would be either completly finish the blade then fit the slot, or make the slot slightly smaller to allow for blade finish. Then I used a Dremmel tool with a burr and fit check fit and check!

JD, This antler was still attached to the skull and I sawed it off close to the skull plate and rounded the bone off to the length I wanted. Then I free handed the pattern I wanted with a pencil. Then I used the Dremmel to rough in the design and used a fine needle file to clean it up. Finally I used a finger nail buffing board with the three or four fine grits to polish!

Steve
--------
Potomac Forge
ABS Apprentice

David Yukon · « **Reply #8 on:** February 07, 2012, 08:02:00 PM »

Great looking knife there, congrats!

Doug Campbell · « **Reply #9 on:** February 07, 2012, 08:03:00 PM »

Nice Steve

Kevin Evans · « **Reply #10 on:** February 07, 2012, 11:03:00 PM »

Good job

loyd · « **Reply #11 on:** February 08, 2012, 05:34:00 AM »

nice, put a brass ring on the tang and wear it on your neck. loyd

kbaknife · « **Reply #12 on:** February 08, 2012, 07:42:00 AM »

I love that thing!

Lamey · « **Reply #13 on:** February 08, 2012, 08:08:00 AM »

I love those primitave friction folders. Good job Steve!!

Lin Rhea · « **Reply #14 on:** February 08, 2012, 01:26:00 PM »

You know in late Winter that white part will fall off.

Just kidding!

It's nice. I'd like to make one myself.

JohnHV · « **Reply #15 on:** February 08, 2012, 01:49:00 PM »

Steve,

Thanks for the response to my question.

Great knife.

tippit · « **Reply #16 on:** February 08, 2012, 02:25:00 PM »

Steve,
Nice job! I've always wanted to try one. Thanks for the post.

akaboomer · « **Reply #17 on:** February 08, 2012, 10:29:00 PM »

Nice little knife! Well done!

Chris

DANA HOLMAN · « **Reply #18 on:** February 09, 2012, 08:31:00 AM »

Steve, Thats very nice, Was it hard to cut the slot in the handle?
Dana

Steve Nuckels · « **Reply #19 on:** February 10, 2012, 10:52:00 AM »

Guys, I have a question, do you like the color that I dyed the antler? Or would it look better natural, darker or lighter? I used Fibings Leather dye.

Lin, I woke up this morning to find it is a shead antler now!!!!!

News:

Author Topic: Primitive Friction Folder, with a question (Read 857 times)

Users currently browsing this topic: