Author Topic: Riser Issues  (Read 870 times)

Offline UnderControl16

  • Trad Bowhunter
  • **
  • Posts: 297
Riser Issues
« on: May 24, 2009, 07:49:00 PM »
Ok so i tried to build a bow with a riser and to say the least it snapped just at the start.

How do you build a bow with a riser? Any advice or place you could point me to on the web would be great.

Offline bjansen

  • Trad Bowhunter
  • **
  • Posts: 2263
Re: Riser Issues
« Reply #1 on: May 24, 2009, 08:45:00 PM »
Glass bow I assume and what kind of riser wood did you use?  A picture would be worth a thousand words on this one...would you happen to have one?

Offline UnderControl16

  • Trad Bowhunter
  • **
  • Posts: 297
Re: Riser Issues
« Reply #2 on: May 25, 2009, 01:44:00 PM »
I could go take one it would just take a second. The riser was birch and then oak and maple limbs.

Offline bjansen

  • Trad Bowhunter
  • **
  • Posts: 2263
Re: Riser Issues
« Reply #3 on: May 25, 2009, 10:16:00 PM »
Try to take one and post it...you will get plenty of feedback from these guys.  Im a little hesitant on the birch riser as birch is somewhat weak (unless heavily laminated)...but post a picture and I bet we can find out what went wrong.

Offline UnderControl16

  • Trad Bowhunter
  • **
  • Posts: 297
Re: Riser Issues
« Reply #4 on: June 16, 2009, 05:50:00 PM »
What did i do wrong?

 

Offline Bert Frelink

  • Trad Bowhunter
  • **
  • Posts: 769
Re: Riser Issues
« Reply #5 on: June 16, 2009, 06:35:00 PM »
Your fade outs are way too steep, look on some of the "buildalongs" and you might get a feel for what they are supposed to look like.
You should probably also back it with something if you are useing Oak/Maple for the limbs.
Bert.

Offline UnderControl16

  • Trad Bowhunter
  • **
  • Posts: 297
Re: Riser Issues
« Reply #6 on: June 16, 2009, 06:43:00 PM »
I meant to say that they are maple limbs backed with oak.

Offline bjansen

  • Trad Bowhunter
  • **
  • Posts: 2263
Re: Riser Issues
« Reply #7 on: June 16, 2009, 06:57:00 PM »
Ah...I was thinking the riser that broke, but it appears it was the limb.

I agree with Bert. It appears there was just too much pressure at the fade out, which can all be worked out when you tiller.

Like Bert said a more even taper on the riser would help (i.e. on a 16" riser, I would have about 6" of transition, a 4" handle then 6" of transition).

I bet when you first had it on the tiller tree the limbs were not tillered and too much pressure was on the fades when you were pulling it... then boom.  When you glue a block to the middle of a board it stiffens that section up but also creates a two natural place for the limbs to want to bend when you pull it back (the fades).  So thinner fades and slower tillering will help ensure you alleviate those preasure points.  So I would try it again and take your time.  The riser and glue up job looks really good though!   Good luck!

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Riser Issues
« Reply #8 on: June 16, 2009, 08:00:00 PM »
It looks to me you have your backing on the belly of your bow. The backing goes on the side away from the archer and the belly faces the archer. Will you post a pic of the entire bow?
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline UnderControl16

  • Trad Bowhunter
  • **
  • Posts: 297
Re: Riser Issues
« Reply #9 on: June 17, 2009, 10:48:00 AM »
Sorry Pat i don't have any complete pictures of the bow seeing as how it's now scrap wood but you would be right that i did have the backing on the wrong side but i wanted to have it on the side of the fades. Does it matter which side you have the layer on?/Did i need a backing?

Offline dutchwarbow

  • Trad Bowhunter
  • **
  • Posts: 326
Re: Riser Issues
« Reply #10 on: June 17, 2009, 01:49:00 PM »
undercontrol, do you have a closeup of the grain? since that might be one of the problems aswell as a hinge in the fades.

you may have needed a backing incase the grain wasn't good enough, but I can't judge without pictures.

Nick
in the old days religion had it's use to keep nations together. Today, religion tears nations apart.

Nick

Offline Steve Kendrot

  • Trad Bowhunter
  • **
  • Posts: 789
Re: Riser Issues
« Reply #11 on: June 18, 2009, 11:25:00 AM »
Have you had a chance to read any of the bowyers bibles or watch hunting the bamboo backed Osage bow? Time spent with these resources can save you a lot of time making kindling.

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Riser Issues
« Reply #12 on: June 18, 2009, 05:01:00 PM »
The back of the bow is under tension stresses and the belly is under compression stresses. The belly can handle grain violations but the back can not! If the bow's back has violated rings a backing strip is recommended to help keep the bow together. It looks to me that your bow broke at a ring violation. Another option, besides a wood backing strip would be rawhide, silk or linen as insurance.
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©