Author Topic: crack in limb glass  (Read 438 times)

Offline USAFdad

  • Trad Bowhunter
  • **
  • Posts: 71
crack in limb glass
« on: October 24, 2012, 11:41:00 AM »
Building a couple TD bows for my boys for Christmas and the riser for one had a critical failure. There is a fracture in the glass of this limb now when it smacked the edge of the bench.
Question is can I save this, would it be fine with tha tip overlays glued over the top?
I already have a new limb kit ready to glue up but hate to waste these if I don't have to.
Thanks for your thoughts on the matter.

Offline USAFdad

  • Trad Bowhunter
  • **
  • Posts: 71
Re: crack in limb glass
« Reply #1 on: October 24, 2012, 11:44:00 AM »
Sorry not good at the picture thing. Trying again                                           [IMG]http://i967.photobucket.com/albums/ae156/hualapai09/2012-10-24063330.jpg[/IMG

Offline USAFdad

  • Trad Bowhunter
  • **
  • Posts: 71
Re: crack in limb glass
« Reply #2 on: October 24, 2012, 11:50:00 AM »

Hopefully third times a charm.

Offline GREG IN MALAD

  • Trad Bowhunter
  • **
  • Posts: 458
Re: crack in limb glass
« Reply #3 on: October 24, 2012, 01:24:00 PM »
I would drill a .050 hole at the end of the crack so it doesn't grow, then fill the crack with thin superglue. With a tip overlay it should be fine. I have repaired similiar cracks this way with good results.
I didnt miss, thats right where I was aiming

Offline Swissbow

  • Trad Bowhunter
  • **
  • Posts: 868
Re: crack in limb glass
« Reply #4 on: October 24, 2012, 02:25:00 PM »
I would use a syringe to inject epoxy under the glass. With a hot air gun you can heat up the epoxy and make it very liquid. Due to the capillarity the epoxy fills out even the smallest crack almost by itself, just make sure to inject enough of it. It works perfect and after the epoxy has cured and everything is cleaned up you barely won't be able to see the repair job.

----------
Andy

Offline LittleBen

  • Trad Bowhunter
  • **
  • Posts: 2970
Re: crack in limb glass
« Reply #5 on: October 24, 2012, 03:43:00 PM »
Both those plans sound solid. I'd probably drill the .050 hole at the tip of the crack as suggested by Greg and then use the epoxy injection as suggested by Andy. Then definately tip overlay. Maybe use some phenolic for the overlay then a bit of hardwood.

Offline USAFdad

  • Trad Bowhunter
  • **
  • Posts: 71
Re: crack in limb glass
« Reply #6 on: October 24, 2012, 04:11:00 PM »
Thanks for the great advise so far. You've just made my day guys. I was hoping that there was a possibility this limb could be saved.
 
So where does one aquire a suitable syringe for the task?  Do I just use any clear epoxy or are we talking smooth-on?

I had planned on phenolic and hardwood tip overlay and I think it's called kwik-it glue, a super glue type of glue I got from a friend.

Online wood carver 2

  • Trad Bowhunter
  • **
  • Posts: 2726
Re: crack in limb glass
« Reply #7 on: October 24, 2012, 06:21:00 PM »
I got an unused but expired syringe from a doctor when I explained that I needed one for injecting glue into cracks to repair furniture.
Once I'm done, I just wash it out so it can be used again. It might have helped that I had just built a nice blanket chest for her.  :knothead:  
Dave.
" Vegetarian" another word for bad hunter.

Offline rmorris

  • Trad Bowhunter
  • **
  • Posts: 1289
Re: crack in limb glass
« Reply #8 on: October 24, 2012, 11:39:00 PM »
Here is a crazy trick for you... Once you follow all of the other advices on stoping and filling the crack  and if you dont want to do an overlay, take a brown sharpie and draw over the crack very lightly . This will nearly make any blimish in the glass go away and you can then put a normal finish over the sharpie. Also if you don't like it , take some alchoal and remove the sharpie.
"Havin' such a good time Oo-de-lally, Oo-de-lally Golly, what a day"

Offline USAFdad

  • Trad Bowhunter
  • **
  • Posts: 71
Re: crack in limb glass
« Reply #9 on: October 25, 2012, 11:22:00 AM »
Thanks again for all the advise.
rmorris, you reminded me of something. I saw the people at Lazy Boy furniture do the brown marker thing on an end table once. They had a whole kit full of different shades. It did work well.

Users currently browsing this topic:

0 Members and 2 Guests are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©