Author Topic: cutting rubber bands  (Read 510 times)

Offline monterey

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 4248
cutting rubber bands
« on: July 24, 2014, 02:18:00 PM »
Here I sit, cutting bike tires into rubber bands.  Its actually sort of an oddly soothing activity!

I'm not sure if these would be best used as huge circular bands, or cut through to make rubber strips.  Any advice from the experienced rubber band form users?
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Offline Swissbow

  • Trad Bowhunter
  • **
  • Posts: 868
Re: cutting rubber bands
« Reply #1 on: July 24, 2014, 02:49:00 PM »
I cut them through, cut them in half lengthwise and knot a loop at the ends. This works best for me.
__________
Andy

Online Sam Harper

  • Trad Bowhunter
  • **
  • Posts: 474
Re: cutting rubber bands
« Reply #2 on: July 24, 2014, 02:59:00 PM »
I just cut little round rubber bands of the inner tube and stretch them across the bow on pegs, like this:

 http://poorfolkbows.com/brecurve4.htm
There are strange things done in the midnight sun by the men who moil for gold.

Offline monterey

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 4248
Re: cutting rubber bands
« Reply #3 on: July 24, 2014, 03:15:00 PM »
Sam, too late for little bands,  but I might try that next time.  Enjoyed your build along!

Andy, bout how many tubes per bow?  Is to be a 68" LB.
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Online jess stuart

  • Trad Bowhunter
  • **
  • Posts: 1722
Re: cutting rubber bands
« Reply #4 on: July 24, 2014, 06:47:00 PM »
I have never tried the bike tubes.  I have bands made from an old truck tube.  I cut them about 2" wide and went around the tube kind of like peeling an apple.  I usually made the strips about 8-10 feet long and wrapped around the entire form, never used the pegs.  They work well and I still use them once in a great while but, the air hose is easier for me.

Offline KenH

  • Trad Bowhunter
  • **
  • Posts: 1042
Re: cutting rubber bands
« Reply #5 on: July 24, 2014, 08:22:00 PM »
Depends a bit on how your form is set up.  I use 1" wide rings of innertube on this and my other forms where the 1/4" diameter dowel pins are set 3/4" below the face of the form.  Hook the innertube ring over one pin, stretch across the lams, hook it over the other pin.  If it's too much stretch, like over a riser, I interlace two rings together and then stretch.

   

Here's the form as I'm clamping down some soaked Red Elm lams to dry them to the complex curves of this Scythian bow.  When these are dry I then glue them up with the belly glass (on top of what you see there).  When that's dry I then I glue on the  back glass as a separate operation.

 
Living Aboard the s/v ManCave

Offline JamesV

  • Trad Bowhunter
  • **
  • Posts: 2027
Re: cutting rubber bands
« Reply #6 on: July 25, 2014, 07:53:00 AM »
I get used tractor inter tubes and spiral cut them into 1 1/2" strips, usually get over 100 feet out of half a tube. Most time the tractor tire dealers have tubes they will give you.

James
Proud supporter of Catch a Dream Foundation
-----------------------------------
When you are having a bad day always remember: Everyone suffers at their own level.

Offline breazyears

  • Trad Bowhunter
  • **
  • Posts: 337
Re: cutting rubber bands
« Reply #7 on: July 25, 2014, 10:27:00 PM »
I like to make strips with bicycle tubes. They have convenient lines that run the length of the tube that make cutting them a snap.
theirs a fly in my soup

Offline monterey

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 4248
Re: cutting rubber bands
« Reply #8 on: July 26, 2014, 12:03:00 AM »
Yes, saw that and used them as guidelines.  Have cut six tubes with about 2/3 being full circle bands and the rest in lengths due to the valve stems.  Guess this calls for a dry run.
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Offline Swissbow

  • Trad Bowhunter
  • **
  • Posts: 868
Re: cutting rubber bands
« Reply #9 on: July 26, 2014, 05:09:00 AM »
A dry run is always a good idea. If your using rather thick lams ( for a heavy draw weight ) you might consider to apply some additional pressure at the fades to make sure you get good glue lines. I use the pieces i cut away from the riser block, because they fit the fades perfectly.

 
__________
Andy

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©