Author Topic: Smooth on form time ?  (Read 1135 times)

Offline Forwardhandle

  • Trad Bowhunter
  • **
  • Posts: 1976
Smooth on form time ?
« on: January 06, 2018, 01:01:00 PM »
Hi Fellas  this is only the secound time I have used smooth on and I glued up a handle on a BBH bow this morning but I have to work tomorrow afternoon so I would like to pull it off the form in the morning, Its curing at room temp but do you guys think it would be safe pull it off the form at only 20 hrs and clean it up with out stressing any thing I relies 24 hrs is the norm ?      
If you fear failure, you will never try ! But never except it!!

Offline Krasus

  • Trad Bowhunter
  • **
  • Posts: 401
Re: Smooth on form time ?
« Reply #1 on: January 06, 2018, 01:30:00 PM »
Hmmm. Depends on how badly you don't want to run the risk of a failure. I always like to be on the safe side and wait. Up to you though. I use a bow oven though and your doing a room temp cure. I'd hold off but that's just my opinion.  :)  good luck

Offline Forwardhandle

  • Trad Bowhunter
  • **
  • Posts: 1976
Re: Smooth on form time ?
« Reply #2 on: January 06, 2018, 01:34:00 PM »
Ok thanks I will just wait the 24 hrs then why risk it I'm just short on time tomorrow but like most things with bows just hurry up and wait !
If you fear failure, you will never try ! But never except it!!

Offline Krasus

  • Trad Bowhunter
  • **
  • Posts: 401
Re: Smooth on form time ?
« Reply #3 on: January 06, 2018, 01:41:00 PM »
I used to be that way with my bowyering but I forced myself to slow down and not rush things. Lot less mistakes made that way.  :D

Offline Forwardhandle

  • Trad Bowhunter
  • **
  • Posts: 1976
Re: Smooth on form time ?
« Reply #4 on: January 06, 2018, 01:54:00 PM »
Yep I normally don't like to take short cuts just was thinking maybe it was set enough for cleaning up but I don't know smooth on
If you fear failure, you will never try ! But never except it!!

  • Guest
Re: Smooth on form time ?
« Reply #5 on: January 07, 2018, 11:44:00 AM »
At 75- 90 degrees and 4 to 6 hours of cure time I have found that the resin is pretty hard... It may not be fully cured but it is hard enough to take out of the form... But being cured at room temperature for 6 hrs I would not stress the limbs for 24 hrs...I post cure my bows in an oven for three hrs at about 150 to make sure they are fully cured... Krasus is right that you should always err to the safe side of things... There is always plenty of other stuff to do while you are waiting...

Offline Crooked Stic

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6075
Re: Smooth on form time ?
« Reply #6 on: January 07, 2018, 11:48:00 AM »
I say you will be ok but just dont bend it for awhile.
High on Archery.

Offline Forwardhandle

  • Trad Bowhunter
  • **
  • Posts: 1976
Re: Smooth on form time ?
« Reply #7 on: January 07, 2018, 12:26:00 PM »
I just waited the full 24 hrs before taking it off I put it under a electric blanket at 104 Deg F for 5 hrs during the cure don't know if it really helps but figured it couldn't hurt , still had time to clean it up and get to short brace before going to work after this bow is done I'm going to build a proper hot box !
If you fear failure, you will never try ! But never except it!!

Offline JamesV

  • Trad Bowhunter
  • **
  • Posts: 2027
Re: Smooth on form time ?
« Reply #8 on: January 11, 2018, 07:20:00 PM »
I cure my risers in my wife's over, with her permission of course.

James
Proud supporter of Catch a Dream Foundation
-----------------------------------
When you are having a bad day always remember: Everyone suffers at their own level.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©