3Rivers Archery



The Trad Gang Digital Market












Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters






LEFT HAND BOWS CLASSIFIEDS TRAD GANG CLASSIFIEDS ACCESS RIGHT HAND BOWS CLASSIFIEDS


« previous next »
Pages: [1]   Go Down

Author Topic: HELP Making Drain Pipe Quiver  (Read 601 times)

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
HELP Making Drain Pipe Quiver
« on: January 16, 2009, 11:02:00 AM »
I have a 3 ft. section of white, 4", thin walled, PVC type sewer drain pipe(unused!) and 2 end caps for it and would like it if maybe some of you could post some pictures of some ideas/projects that you have come up with for using it as a side/back quiver. Kinda like the ones that have a section cut out of the side for easy arrow access. I did a search on this website already but couldn't find many pics. of homemade ones. Thanks a bunch for any help!   :)
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under

Offline ishiwannabe

  • Trad Bowhunter
  • **
  • Posts: 4360
Re: HELP Making Drain Pipe Quiver
« Reply #1 on: January 16, 2009, 11:12:00 AM »
I made one, but dont have any pics.
I used 3 ", and it will hold about a half dozen arrows.
It works well as it is closed and protecs the arrows VERY well. I put a clean out on the upper section to facilitate arrow insertion and removal after the hunt.
For single arrow removal, I cut an oblong oval into the lower section, three inches up from the end. I need to widen it though to make it a bit better.
To help with noise I covered it with camo from years ago, then I wove some 550 cord for the strap.
Hope it helps.
Logged
"I lost arrows and didnt even shoot at a rabbit" Charlie after the Island of Trees.
                         -Jamie

Offline Bjorn

  • Trad Bowhunter
  • **
  • Posts: 8789
Re: HELP Making Drain Pipe Quiver
« Reply #2 on: January 16, 2009, 11:43:00 AM »
This one is from 3 1/2" thin walled stuff. Plugged with a wood round cut from a cedar shingle. Camo cloth from a fabric store was glued with barge cement-but any WP cement will do.
 
The straps coulda' been better, maybe next time....
Logged

Offline Bjorn

  • Trad Bowhunter
  • **
  • Posts: 8789
Re: HELP Making Drain Pipe Quiver
« Reply #3 on: January 16, 2009, 11:48:00 AM »
Oh yeah, some camo cloth becomes way noisy when glued to a pipe........found that out the hard way. Ended up covering the first attempt with fleece camo material.
Logged

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
Re: HELP Making Drain Pipe Quiver
« Reply #4 on: January 16, 2009, 11:48:00 AM »
This is great, guys. Keep'em comin'. So you're just using foam in the bottom for broadheads and fieldtips?
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under

Offline Benha

  • Trad Bowhunter
  • **
  • Posts: 933
Re: HELP Making Drain Pipe Quiver
« Reply #5 on: January 16, 2009, 01:16:00 PM »
Can't help with your project but wanted to say hello. I'm in Radcliff.
Logged

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
Re: HELP Making Drain Pipe Quiver
« Reply #6 on: January 16, 2009, 05:11:00 PM »
Hello George. I have you on my buddy list. Where do you shoot at mostly?
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under

Offline OkKeith

  • Trad Bowhunter
  • **
  • Posts: 1237
Re: HELP Making Drain Pipe Quiver
« Reply #7 on: January 16, 2009, 05:27:00 PM »
Hey Douglas,

Here are some pics of one I made. Have made several more since this one, but no pics. They are all basically the same though with minor modifications. NO, that is not me modeling the quiver.

 

 

I used the 4 inch thin walled stuff. The inside is covered with the adhesive backed foam used in crafty type projects to diminish noise. I used nylon webbing for straps with quick snap type buckles.

I have turkey hunted and hog hunted with it and it works great for me. I am taller than the model so when I wear it and duck under branches it does not hang up. You can crawl around on your belly all day with and it does fine.

One addition to all the ones i make now is a sternum strap like you would find on a back pack. That way you won't have to be hitching up the shoulder straps all the time. I can get 6 broadhead arrows and 3 "bunny buster" arrows in it.

Make you one. They are inexpensive. Make the first one look as good as you can, if it's not quite right give it away and make you another. I just use dead flat spray paint (2-3 coats) on the outside.

OkKeith
Logged
In a moment of decision the best thing you can do is the right thing. The worst thing you can do is nothing.
Theodore Roosevelt

Offline Benha

  • Trad Bowhunter
  • **
  • Posts: 933
Re: HELP Making Drain Pipe Quiver
« Reply #8 on: January 16, 2009, 07:25:00 PM »
Yellowbank WMA at the 20 target 3D range.
Logged

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
Re: HELP Making Drain Pipe Quiver
« Reply #9 on: January 16, 2009, 09:21:00 PM »
Very nice, OkKeith. How long is it? I think I need mine to be shorter. I'm wanting to carry it more at an angle or under my arm on my side? Mine will probably be very similar to yours though. Thanks for your reply.
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under

Offline cahaba

  • Trad Bowhunter
  • **
  • Posts: 1773
Re: HELP Making Drain Pipe Quiver
« Reply #10 on: January 17, 2009, 01:44:00 AM »
Heres a link that shows how to make a back quiver out of pvc. It dont have the side removal.

 http://www.youtube.com/watch?v=_D4IDg9japI&feature=related
Logged
cahaba: A Choctaw word that means
"River from above"

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
Re: HELP Making Drain Pipe Quiver
« Reply #11 on: January 17, 2009, 05:59:00 AM »
Cahaba, I just watched the youtube vid from the link you provided. Now that was cool. Actually, I have a 10 ft. section so I can cut it into 3 sections and make my 2 sons a back quiver each, and there's can be like the one in the vid. Thanks a bunch for your reply.   :thumbsup:
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under

Offline vtmtnman

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 1667
Re: HELP Making Drain Pipe Quiver
« Reply #12 on: January 17, 2009, 06:34:00 AM »
Quote
Originally posted by cahaba:
Heres a link that shows how to make a back quiver out of pvc. It dont have the side removal.

  http://www.youtube.com/watch?v=_D4IDg9japI&feature=related  
I love the internet....  :readit:    :thumbsup:  

I see I'm not the only one trying to figure out how to make a sewer pipe quiver.  :D
Logged
>>>>--TGMM family of the bow--->

Offline KYArcher

  • Trad Bowhunter
  • **
  • Posts: 824
Re: HELP Making Drain Pipe Quiver
« Reply #13 on: January 17, 2009, 09:32:00 AM »
Interesting, you guys got me thinking about making one.  :thumbsup:  
                          KY  :archer:
Logged

Offline Swamp Pygmy

  • Trad Bowhunter
  • **
  • Posts: 402
Re: HELP Making Drain Pipe Quiver
« Reply #14 on: January 17, 2009, 12:04:00 PM »
bjorn that is neat.

Thought about something like that myself but yours is much nicer that what I was picturing.
Logged
South Louisiana Longbow Shooter

The only trophy you'll ever bring home is a good time. The rest is just meat. -SP

Offline OkKeith

  • Trad Bowhunter
  • **
  • Posts: 1237
Re: HELP Making Drain Pipe Quiver
« Reply #15 on: January 20, 2009, 01:39:00 PM »
Douglas,

I shoot a full length arrow (32 inch shaft plus nock and broadhead) so for me it must be fairly long. Also don't forget that you need some extra length to lift out the arrows.

Good Luck,
OkKeith
Logged
In a moment of decision the best thing you can do is the right thing. The worst thing you can do is nothing.
Theodore Roosevelt

Offline ishoot4thrills

  • Trad Bowhunter
  • **
  • Posts: 3445
Re: HELP Making Drain Pipe Quiver
« Reply #16 on: January 20, 2009, 01:53:00 PM »
Okay, OkKeith, thanks for the advice. I'll sure keep that in mind.
Logged
58" JK Traditions Kanati Longbow
Ten Strand D10 String
Kanati Bow Quiver
35/55 Gold Tip Pink Nugents @ 30"
3 X 5" Feathers
19.9% FOC
49# @ 26.75"
165 FPS @ 10.4 GPP (510 gr. hunting arrow)
171 FPS @ 9.7 GPP (475 gr. 3D arrow)
3 Fingers Under
Pages: [1]   Go Up
« previous next »

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©