Author Topic: Selfbow repair  (Read 421 times)

Offline rascal

  • Trad Bowhunter
  • **
  • Posts: 402
Selfbow repair
« on: February 13, 2010, 01:30:00 PM »
Looking for some input on what I think is a pretty simple repair, I have a 59" nock to nock osage orange self bow that draws 83# at my 25 1/2" draw that has a small splinter of wood that popped loose from the back of the bow.  The limb is 1 3/8" wide at the site of the sliver if it makes a difference and the sliver is less than the size of a flat tooth pick.  It is in the first 3rd of the limb closest to the handle, about 2" long and still attached at the point closest to the handle.

I have some sinew Ive been collecting and thaught that I could wrap the area but I have no idea how to do this properly or if it is the correct repair for the damage.  I could probably chase a new ring and tiller it out as a lighter bow as well.

Any ideas??
Hunt fair, hunt hard, no regrets.

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Selfbow repair
« Reply #1 on: February 13, 2010, 03:35:00 PM »
I would add super glue under the splinter and clamp it. If the bow is tillered you could put a permanent sinew wrap over the splinter so it won't raise up.   You could also put a rawhide backing over both limbs after super glue in the splinter. That will probably hold it too.
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline rascal

  • Trad Bowhunter
  • **
  • Posts: 402
Re: Selfbow repair
« Reply #2 on: February 13, 2010, 06:09:00 PM »
What adhesive do you use to put a sinew wrap on?  And would it hurt anything to put a matching wrap on the lower limb as an accent?
Hunt fair, hunt hard, no regrets.

Offline shamus

  • Trad Bowhunter
  • **
  • Posts: 354
Re: Selfbow repair
« Reply #3 on: February 13, 2010, 07:09:00 PM »
glue the splinter down with super glue.

Then, wrap the area with #4 nylon serving and coat it in 2-ton epoxy.

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Selfbow repair
« Reply #4 on: February 13, 2010, 10:50:00 PM »
What Shamus said or silk wrap with super glue. For sinew use hide glue. Yes, you can add another wrap on the opposite limb for symmetry.
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline John Scifres

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 4540
Re: Selfbow repair
« Reply #5 on: February 13, 2010, 11:08:00 PM »

Yuck, splinter!

 
Hmmm, superglue  :)
 
And sinew.

 
Rough up the surface for 1" above and below the splinter.
Take a kid hunting!

TGMM Family of the Bow

Offline John Scifres

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 4540
Re: Selfbow repair
« Reply #6 on: February 13, 2010, 11:13:00 PM »

A little Knox gelatin dissolved in hot water and then kept warm with an old coffee maker hotplate.

 
I like to put some longwise and then wrap it for at least an inch above and below.

Make sure your tiller is pretty good before since you can't really do much about it afterwards.  Sometimes you just have to live with a stiff spot where you did your repair.
Take a kid hunting!

TGMM Family of the Bow

Offline rascal

  • Trad Bowhunter
  • **
  • Posts: 402
Re: Selfbow repair
« Reply #7 on: February 15, 2010, 06:57:00 PM »
Thanks for all who responded, I am always impressed with the help I find here.  Pictures were especially handy John.
Hunt fair, hunt hard, no regrets.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©