The Cyber Camp of Traditional Bowhunters
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Help
Login
Register
Trad Gang
»
Main Boards
»
The Bowyer's Bench
»
strip for bow form question
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: strip for bow form question (Read 521 times)
Jerry Gille
Trad Bowhunter
Posts: 187
strip for bow form question
«
on:
April 07, 2014, 01:52:00 PM »
I am making a new bow form and am at the point where I want to glue a piece of something on the bottom form to smooth it out. I routed it out but still like to have something glued down to lay the bow on. I've used Bingham's "formica" in the past. Always looked a lot like fiberglass to me. I've also used a piece of glass. Both have worked fine on past forms. But I'm a tight wad and don't want to use a good piece of glass for this new form nor do I want to order a piece of formica from Binghams. Can anyone suggest something similar that I may be able to pick up at a home store locally?
Thanks!
Logged
jess stuart
Trad Bowhunter
Posts: 1722
Re: strip for bow form question
«
Reply #1 on:
April 07, 2014, 02:42:00 PM »
I was able to score a fairly large piece of formica from the left over pile in a cabinet shop. I think it was free for the asking. In fact years back Binghams would actually send formica instead of glass. Some use a parallel lam of wood instead of formica either will work fine.
Logged
fujimo
Trad Bowhunter
Posts: 3619
Re: strip for bow form question
«
Reply #2 on:
April 07, 2014, 03:13:00 PM »
i used a piece of hickory i had, ran it through the thickness sander- got it perfectly flat, and abou 1/8 " thick- glued that on, then sealed it and waxed it- very happy!!
Logged
MB_Sweden
Trad Bowhunter
Posts: 100
Re: strip for bow form question
«
Reply #3 on:
April 07, 2014, 03:26:00 PM »
Im using aluminum strip, 1mm / 0,040" thick
Logged
Martin From Sweden
Magnum in Ms
Trad Bowhunter
Posts: 294
Re: strip for bow form question
«
Reply #4 on:
April 07, 2014, 08:16:00 PM »
I use a 1/16" strip of aluminum from Lowes
Logged
Every one is ignorant its just on different subjects
fujimo
Trad Bowhunter
Posts: 3619
Re: strip for bow form question
«
Reply #5 on:
April 07, 2014, 08:46:00 PM »
what do you glue the ali down with- smooth on?
Logged
Robertfishes
Trad Bowhunter
Posts: 3490
Re: strip for bow form question
«
Reply #6 on:
April 08, 2014, 09:32:00 AM »
I have 3 forms, I used 040 Black fiberglass on each one. I used 3M "High Strength 90" high temp spray on contact cement glue to glue a set of red elm tapers to the form and a piece of fiberglass to the tapers for the final piece. I could have stopped with the tapers but I always thought the fiberglass might be easier to wax and clean than a wood surface. I can see and feel any small pieces of anything on the smooth black glass.
Logged
Pat B
TG HALL OF FAME
Trad Bowhunter
Posts: 15027
Re: strip for bow form question
«
Reply #7 on:
April 08, 2014, 10:58:00 AM »
Contact cement should hold the aluminum strip down.
Logged
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow
Jerry Gille
Trad Bowhunter
Posts: 187
Re: strip for bow form question
«
Reply #8 on:
April 08, 2014, 11:40:00 AM »
Thanks for the suggestions everyone! Any idea what department the aluminum strip would be in at Lowe's?
I got a guy looking into some scrap formica from a cabinet shop too.
Logged
JamesV
Trad Bowhunter
Posts: 2027
Re: strip for bow form question
«
Reply #9 on:
April 08, 2014, 01:52:00 PM »
Most local custom cabinet shops have scrap formica and will cut it for cheap, if not free. Take one of your bows along to show and I bet they will help you out.
Logged
Proud supporter of Catch a Dream Foundation
-----------------------------------
When you are having a bad day always remember: Everyone suffers at their own level.
D
Trad Bowhunter
Posts: 1509
Re: strip for bow form question
«
Reply #10 on:
April 08, 2014, 10:59:00 PM »
Its in the nuts and bolt section. That's where I got mine anyway. I got one that is 3/16ths I think and screwed it down and recessed the screew head down in it and then filled the holes with bondo. I didn't think any glue would work on aluminum for that until now..lol Glueing it would be a better idea..lol
Logged
Magnum in Ms
Trad Bowhunter
Posts: 294
Re: strip for bow form question
«
Reply #11 on:
April 08, 2014, 11:07:00 PM »
I used a high temp spray on glue on one form and it worked fine. The last form I made I used smooth-on and it came loose on the ends.
Logged
Every one is ignorant its just on different subjects
critman
Trad Bowhunter
Posts: 376
Re: strip for bow form question
«
Reply #12 on:
April 09, 2014, 12:38:00 AM »
X2 on the 1/16 aluminum from Lowes.
Logged
snapper1d
Trad Bowhunter
Posts: 226
Re: strip for bow form question
«
Reply #13 on:
April 09, 2014, 09:08:00 AM »
I have used wood like fijimo.Th aluminum scare me because it would rather bend and kink in one place than bend and curve around like wood or formica does.When putting aluminum down if you kink it you cant get that kink back out and the more you try the worse it gets and then its just an expensive piece of recycle material.
Logged
snapper1d
Trad Bowhunter
Posts: 226
Re: strip for bow form question
«
Reply #14 on:
April 09, 2014, 09:14:00 AM »
Also to add.If you use 2 strips of wood on top as your pressure strips and use a little glue between them then you will have a top pressure strip formed perfect for every time you make a bow.
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
Trad Gang
»
Main Boards
»
The Bowyer's Bench
»
strip for bow form question
Users currently browsing this topic:
0 Members and 1 Guest are viewing this topic.
Contact Us
|
Trad Gang.com ©
|
User Agreement
Copyright 2003 thru 2024 ~ Trad Gang.com ©