Author Topic: What to use for protecting form  (Read 2809 times)

Offline Lee Lobbestael

  • Trad Bowhunter
  • **
  • Posts: 489
What to use for protecting form
« on: May 01, 2018, 06:07:15 AM »
Whay do you guys use to protect your bow from getting glued to your form during glue up? I have been using saran wrap but it seems a bit thin and tears easily

Offline Bowjunkie

  • Trad Bowhunter
  • **
  • Posts: 2324
Re: What to use for protecting form
« Reply #1 on: May 01, 2018, 07:48:59 AM »
Saran Wrap. Every bow blank has come right off for me and never leaves any glue on the press. I put a layer on the press, glue up and assemble the bow, pull the lams down into the fadeouts with tape, then another layer of Saran Wrap on top so the pressure strip and air hose doesn't touch the glue.

Offline C. Johnson

  • Trad Bowhunter
  • **
  • Posts: 419
Re: What to use for protecting form
« Reply #2 on: May 01, 2018, 08:03:40 AM »
I use shrink wrap. Like what they use in a warehouse to wrap a pallet of boxes together so they don't fall off the pallet when being moved by forklift. It's pretty much Saran wrap, only a little heavier and stronger.  I buy it at Home Depot/Lowe's.

Offline Bowjunkie

  • Trad Bowhunter
  • **
  • Posts: 2324
Re: What to use for protecting form
« Reply #3 on: May 01, 2018, 08:17:44 AM »
I have a bunch of that. Maybe I'll try it next time. It would be good for pulling the lams down together too.

Online Crooked Stic

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6075
Re: What to use for protecting form
« Reply #4 on: May 01, 2018, 08:26:34 AM »
3 to 4 coats of paste wax on the form surface and a couple of inches down each side dont hurt either.
High on Archery.

Online kennym

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 17339
Re: What to use for protecting form
« Reply #5 on: May 01, 2018, 08:33:13 AM »
The cheap stuff like Saran Wrap works well for me. Don’t cling as well to everything you don’t want it to.

May try the stuff Craig uses, always up for sumpin better!
Stay sharp, Kenny.

   https://www.kennysarchery.com/

Offline Flem

  • Trad Bowhunter
  • **
  • Posts: 2985
  • "Don't quote me on that!"
Re: What to use for protecting form
« Reply #6 on: May 01, 2018, 08:56:08 AM »
I have a hard time keeping saran from bunching up, so I started using parchment paper or freezer paper depending on cooking temp.

Offline John Malone

  • Trad Bowhunter
  • **
  • Posts: 699
Re: What to use for protecting form
« Reply #7 on: May 01, 2018, 01:26:41 PM »
I use unibond, freezer paper, waxed paper works great. Also I use lots of paste wax like crooked stick.
Life is to short to pass up anything that could potentially be bow wood!

Offline Zradix

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 5798
Re: What to use for protecting form
« Reply #8 on: May 01, 2018, 01:53:21 PM »
I use shrink wrap. Like what they use in a warehouse to wrap a pallet of boxes together so they don't fall off the pallet when being moved by forklift. It's pretty much Saran wrap, only a little heavier and stronger.  I buy it at Home Depot/Lowe's.

I think I use the same stuff....though it isn't actually shrink wrap.
This stuff is for wrapping boxes to keep on pallets too...but it is just thicker stronger "saran" wrap

« Last Edit: May 01, 2018, 04:48:17 PM by Zradix »
If some animals are good at hunting and others are suitable for hunting, then the Gods must clearly smile on hunting.~Aristotle

..there's more fun in hunting with the handicap of the bow than there is in hunting with the sureness of the gun.~ F.Bear

Offline C. Johnson

  • Trad Bowhunter
  • **
  • Posts: 419
Re: What to use for protecting form
« Reply #9 on: May 01, 2018, 11:12:52 PM »
I use shrink wrap. Like what they use in a warehouse to wrap a pallet of boxes together so they don't fall off the pallet when being moved by forklift. It's pretty much Saran wrap, only a little heavier and stronger.  I buy it at Home Depot/Lowe's.

I think I use the same stuff....though it isn't actually shrink wrap.
This stuff is for wrapping boxes to keep on pallets too...but it is just thicker stronger "saran" wrap

Yep, that's exactly what I use.

Offline Bowjunkie

  • Trad Bowhunter
  • **
  • Posts: 2324
Re: What to use for protecting form
« Reply #10 on: May 02, 2018, 05:42:35 AM »
Yep that's the stuff. Mine is much narrower, 4" wide I think, on a single handle that's used as a brake to stretch it tight or break it off. It's fast to use.

Offline Forwardhandle

  • Trad Bowhunter
  • **
  • Posts: 1976
Re: What to use for protecting form
« Reply #11 on: May 02, 2018, 03:17:04 PM »
I used Saran Wrap but didn't like it I have washers on my form to hold the lams and had to tear threw it to get it to work so I pulled it off and put green frog tape on the form and made a Saran Wrap cradle and after all my lams where in placed wrapped it over the lams raised the washers and it worked good for me but I have a big roll of the shrink wrap I'm going to try next !
If you fear failure, you will never try ! But never except it!!

Offline monterey

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 4248
Re: What to use for protecting form
« Reply #12 on: May 02, 2018, 06:00:00 PM »
I had trouble controlling the Saran wrap so next came waxed paper and that is working pretty good.
Monterey

"I didn't say all that stuff". - Confucius........and Yogi Berra

Shredd

  • Guest
Re: What to use for protecting form
« Reply #13 on: May 02, 2018, 09:08:43 PM »
I just have one piece of 4mil plastic sheeting that is about 7" wide running length wise on top of the form and then one piece about 4" wide on top of the bow being glued...  I get about 5-8 bows out of it before I have to change it...

Offline Holm-Made

  • Trad Bowhunter
  • **
  • Posts: 1505
Re: What to use for protecting form
« Reply #14 on: May 02, 2018, 11:58:51 PM »
I use two layers or Saran Wrap on the form and one layer on top of bow.

Offline bamboo

  • Trad Bowhunter
  • **
  • Posts: 1161
Re: What to use for protecting form
« Reply #15 on: May 03, 2018, 06:18:44 AM »
carefully wrap the entire form w/two layers of shrink wrap---lay up your bow and pressure strips --tape down firmly[cheap electric tape works great!]--wrap over the stack and strips --glue problems -no more !
Mike

Online Tim Finley

  • Trad Bowhunter
  • **
  • Posts: 1031
Re: What to use for protecting form
« Reply #16 on: May 10, 2018, 11:47:56 AM »
I use butchers plastic it far heavier than saran wrap and doesn't tear. I've used it for almost 30 years its a lot easier to use than saran wrap or palet wrap . It is the plastic wrap they wrap the meat in before they wrap with paper . It comes in 18" rolls and is about 1/2 mile long I cut the strips down to 9 inches wide so I get double out of the roll . I go through about one roll a year I use it for packing in shipping also.

Offline KenH

  • Trad Bowhunter
  • **
  • Posts: 1042
Re: What to use for protecting form
« Reply #17 on: May 10, 2018, 01:35:52 PM »
Someone has to say it, so I will -- practice safe bowbuilding, use a giant condom on your form. :campfire:
Living Aboard the s/v ManCave

Shredd

  • Guest
Re: What to use for protecting form
« Reply #18 on: May 10, 2018, 03:22:52 PM »
Yep....  Said It...    :laugh: :laugh:

Offline canopyboy

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 3106
Re: What to use for protecting form
« Reply #19 on: May 10, 2018, 10:02:17 PM »
I’m not sure anyone actually had to say that...  :knothead:

Pallet wrap here.
TGMM Family of the Bow
Professional Bowhunters Society

"The earth has its music for those who will listen." - Santayana

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©