Author Topic: It’s in the oven! (Read 6714 times)

buddyb · « **Reply #20 on:** February 21, 2019, 11:15:59 AM »

Good looking bow, as others have said, can't wait to see it finished.

ztontonz · « **Reply #21 on:** February 22, 2019, 07:49:00 AM »

Quote from: Bvas on February 21, 2019, 10:42:01 AM

Nice!!!
Looking forward to seeing it finished

Yes that is right, I sanded down the side of the lumbs

ztontonz · « **Reply #22 on:** February 22, 2019, 01:05:42 PM »

Update today with tips gled at 60”. Getting close with still a couple pounds to loose until desired draw weight. Really happy about the way it’s coming along so far:

Flem · « **Reply #23 on:** February 22, 2019, 01:43:47 PM »

Looking good! Got some Pom-Poms there. Makes me think I need some fuzzy dice string silencers

Forwardhandle · « **Reply #24 on:** February 22, 2019, 02:10:47 PM »

I like the limb profile are you tillering in positive tiller the bottom limb looks a lot stiffer from the pic maybe its just the pic ?

skeaterbait · « **Reply #25 on:** February 22, 2019, 02:13:53 PM »

Quote from: lignaphile on February 22, 2019, 01:43:47 PM

Looking good! Got some Pom-Poms there. Makes me think I need some fuzzy dice string silencers

Fuzzy dice.... hmmmmm

Shredd · « **Reply #26 on:** February 22, 2019, 07:18:30 PM »

Fuzzy Dice?? Could start a new trend...

Mike L. · « **Reply #27 on:** March 14, 2019, 10:43:10 AM »

I really like the way that turned out. How’s it shoot?

Mike

ztontonz · « **Reply #28 on:** March 18, 2019, 03:32:06 PM »

Quote from: TattooDave on February 21, 2019, 10:03:20 AM

Looking good! Question for you. You said the tiller was way off, are you guys making tiller adjustments by removing material off the sides of the limbs, as to not loose too much fiberglass off the belly?

Tattoo Dave

Yes that's what I do. It's only my second bow so I am no expert but I will not want to sand down the fiber unless the bow comes out really over expected poundage

ztontonz · « **Reply #29 on:** March 18, 2019, 03:43:49 PM »

Did not have much time to work on the bow lately.
First shooting report says it's not a quiet bow if there is no POM POM on the string! but fairly fast. But well, it's hard to compare to any other bow I know since this one is only 34#@28" (for the wife). The only other bow I could compare it with is an old 30# yellow fiber glass bear bow. Of course the bear bow is not as loud but certainly not as fast neither.

I guess I'll just have to build a 50# with the same design to know what it's really worth. I would probably make it 58". I'm thinking shorter would reduce a little bit preload

goobersan · « **Reply #30 on:** March 30, 2019, 09:19:58 AM »

ztontonz · « **Reply #31 on:** April 05, 2019, 12:26:14 PM »

Here are a couple pictures of the finished bow. I made a new string with less strand off astro and it really quieted the bow down.

Hard to take pictures that do the nice wood justice with such a shiny finish, but the wife is really happy with it. And that’s what really counts

Buemaker · « **Reply #32 on:** April 05, 2019, 12:28:03 PM »

Turned out very nice, what kind of finish are you using?

ztontonz · « **Reply #33 on:** April 05, 2019, 12:33:52 PM »

This one shows a little better

ztontonz · « **Reply #34 on:** April 05, 2019, 12:38:05 PM »

I am using 2 components PU in rattle can (automotive stuff). I am happy with the result. It’s durable. But Not really economical. Approximately 1 can a bow. 20€/ can.
But i don’t have a compressor and this gets the job done

JWheel · « **Reply #35 on:** April 05, 2019, 03:59:32 PM »

That's super purty!...nice job! I like the overlays on the belly too

Kbob · « **Reply #36 on:** April 05, 2019, 05:05:58 PM »

Beautiful!, I might have missed it earlier in the thread but what are your riser woods?

Flem · « **Reply #37 on:** April 05, 2019, 05:13:05 PM »

That is really sharp looking

I keep offering to make my wife a bow, so far no interest

ztontonz · « **Reply #38 on:** April 06, 2019, 04:23:20 AM »

Quote from: Kbob on April 05, 2019, 05:05:58 PM

Beautiful!, I might have missed it earlier in the thread but what are your riser woods?

Kingwood and amaranth

News:

Author Topic: It’s in the oven! (Read 6714 times)

Shredd

Users currently browsing this topic: