Author Topic: Tips & Tricks TD Riser ? (Read 3548 times)

Shredd · « **Reply #20 on:** October 31, 2019, 02:14:19 PM »

Good deal, mr. Fancy Pants...

Forwardhandle · « **Reply #21 on:** October 31, 2019, 03:05:20 PM »

How are you guys aligning your limbs before drilling the alignment holes when using Kenny's method ?

Crooked Stic · « **Reply #22 on:** October 31, 2019, 03:12:07 PM »

Run a string right across the center of both limb bolts over the limb ends with a weight on each end to keep it tight. And move your limbs center the string on the tips still keeping it centered on the riser.
My jig is prolly fancier than your Shredd.

Forwardhandle · « **Reply #23 on:** October 31, 2019, 03:21:59 PM »

Thanks Mike that's how I do my one peace bows , sounds the same with the exception of the bolts , that is a pretty fancy jig you got there, but I don't know about your pants

Shredd · « **Reply #24 on:** October 31, 2019, 03:24:48 PM »

You can sit the un-tapered limbs and the riser on a very flat surface and drill all your holes... Or you can drill the bolt holes and do all your limb shaping and then string up the bow and if a limb is a tad out of alignment you can move the limb over a bit and then drill your holes... In the second method just make sure the a limb does not get knocked to one side and fold up on you.... Also in the second method all the pressure will be on one side of the bolt so your bolt hole will be slightly out of allignment... So I would start with 5/16" holes in your limbs and then maybe widen them later on if the bolt does not line up to go in...

Shredd · « **Reply #25 on:** October 31, 2019, 03:35:37 PM »

Yeah... But mine is bigger...

I just have this machined last week... I am gonna have more holes drilled in it... Other than the pin holes, right now I have 5/16" and 11/32" holes drilled in it...

Here is my latest project... Sold to my friends nephew... 45#

Mad Max · « **Reply #26 on:** October 31, 2019, 07:40:40 PM »

The bow looks good rich
do you use 5/16" dowels ?

Crooked Stic · « **Reply #27 on:** October 31, 2019, 08:22:37 PM »

Do ya clamp that jig to a table top on its side or what.?

Shredd · « **Reply #28 on:** October 31, 2019, 09:35:24 PM »

1/4" pins...

Yes... Clamp it to the table on it's side... Tried using the drill press, the holes were accurate but it was a PITA... I tried drilling with a hand held drill but my holes were off a tad... I now use a 1 1/2" block of wood in unison with the jig and a hand held drill and I get precise holes...

Crooked Stic · « **Reply #29 on:** November 01, 2019, 01:01:59 PM »

This is better.

Sent from my LM-X410.F using Tapatalk

Flem · « **Reply #30 on:** November 01, 2019, 03:49:26 PM »

I like that Sheoak

That full draw profile looks pretty sweet too!

Ritchie, I have a centering jig that I think I used once. Wasn't useful for anything I was doing. Be happy to donate it to your cause if you can use it.

Forwardhandle · « **Reply #31 on:** November 01, 2019, 04:22:47 PM »

I will PM you when I get home !

Crooked Stic · « **Reply #32 on:** November 01, 2019, 04:51:07 PM »

That one would be the one you want with the removable pilots. put the 1/4 and the 27/64 or whatever in and drill both holes at once and get perfect spacing. will work but not perfect.

Roy from Pa · « **Reply #33 on:** November 01, 2019, 05:26:30 PM »

Yer ah good man, Clem...

Flem · « **Reply #34 on:** November 01, 2019, 06:40:22 PM »

Roy, your gonna make me wet myself

Shredd · « **Reply #35 on:** November 01, 2019, 07:06:53 PM »

Nice set-up Stic...

Thanks Flem... That is about as light as it gets... The color can vary... This is actually my first finished take-down... I did not want to get too complicated... I wish I would have put a smaller radius for the accents though... That would have put them a little more center in the riser...

Roy from Pa · « **Reply #36 on:** November 01, 2019, 07:59:09 PM »

Ya Shreddy, I don't like it either.

LOL

Shredd · « **Reply #37 on:** November 01, 2019, 09:34:39 PM »

BO-R · « **Reply #38 on:** November 03, 2019, 09:01:18 AM »

Great info guy's
I did it the same way with either bingham jig, self centering jig as shown.
got tired of all that a few years ago invested in a used mill/drill for about 800.00 bucks.
rigged up with a DRO and I can drill pads to exact specs each time.
the mill also is good for flycutting pads, and wedge are of limbs.

News:

Author Topic: Tips & Tricks TD Riser ? (Read 3548 times)

Shredd

Shredd

Shredd

Shredd

Shredd

Shredd

Users currently browsing this topic: