3Rivers Archery



The Trad Gang Digital Market













Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters






LEFT HAND BOWS CLASSIFIEDS TRAD GANG CLASSIFIEDS ACCESS RIGHT HAND BOWS CLASSIFIEDS


Author Topic: ? regarding Ashby FOC  (Read 440 times)

Offline shortstroke 91

  • Trad Bowhunter
  • **
  • Posts: 671
? regarding Ashby FOC
« on: July 02, 2009, 08:03:00 PM »
Just tested my new arrows, GT 1535 cut 28&1/4" from the valley. 100 grain brass adapters and 125 grain heads footed with 2.5" of 2117 total length is 29.5". Weight is 530 grains and FOC is 19%. I left the brass insert out of one and used the factory aluminum insert, this dropped the weight down to 445 grains and my FOC to 15%.
When shooting there is a small ammount of fishtailing on the 530 but the 445 is like a laser beam. I'm only shooting #45 @ my 28" draw and want all the help I can get, so should I stick with the 445 and replace the brass inserts with the aluminum since I'm only loosing 4% foc and 85 grains of mass?
shortstroke 91
TBOT Life Member
 
"BLOOD MAKES THE GRASS GROW"

Offline J-dog

  • Trad Bowhunter
  • **
  • Posts: 2006
Re: ? regarding Ashby FOC
« Reply #1 on: July 02, 2009, 08:09:00 PM »
Do not think that is enough to be stressing, good arrow flight is a major key to shootin through em. 445 and 45!

J
Always be stubborn.

Captain hindsight to the rescue!

Offline ozy clint

  • Trad Bowhunter
  • **
  • Posts: 2661
Re: ? regarding Ashby FOC
« Reply #2 on: July 02, 2009, 08:15:00 PM »
sounds like the heavier arrow is a bit weak in spine. do you have room to shorten it? try cutting 1/4" off the nock end. repeat if still weak. cut less off between testing if you like. carbons stiffen up quick when cut shorter. if you have enough arrow that is what i would do. you'll only lose a few grains in mass. eg, those arrows are somewhere in the 7gr/" range. cutting them half an inch shorter you only lose 3.5 grs. not going to notice it.

if you reach your minimum arrow length and they are still weak you could also try 50gr inserts.
 that would mean you have less to cut off before you get to where it will tune.
Thick fog slowly lifts
Jagged peaks and hairy beast
Food for soul and body.

Border black douglas recurve 70# and 58# HEX6 BB2 limbs

Offline shortstroke 91

  • Trad Bowhunter
  • **
  • Posts: 671
Re: ? regarding Ashby FOC
« Reply #3 on: July 02, 2009, 08:17:00 PM »
Don't have any room to cut, only about 1/4" of shaft hanging off now and don't want the broadhead any closer than that.
shortstroke 91
TBOT Life Member
 
"BLOOD MAKES THE GRASS GROW"

Offline Jesse Peltan

  • Trad Bowhunter
  • **
  • Posts: 439
Re: ? regarding Ashby FOC
« Reply #4 on: July 02, 2009, 08:24:00 PM »
You have to tune your setup.

Offline Mo. Huntin

  • Trad Bowhunter
  • **
  • Posts: 734
Re: ? regarding Ashby FOC
« Reply #5 on: July 02, 2009, 08:31:00 PM »
I would definately just shoot the factory insert that is flying so well then.

Offline shortstroke 91

  • Trad Bowhunter
  • **
  • Posts: 671
Re: ? regarding Ashby FOC
« Reply #6 on: July 02, 2009, 08:55:00 PM »
I HATE it when I jump to conclusions!  :banghead:  After shooting with Snuffers and Magnus 1 broadheads the heavy shaft is flying great and stacking on top of each other. The lighter shaft is showing a little stiff and planing left. Sorry for the bother  ;) , should have been more patient and tested all the perameters.
shortstroke 91
TBOT Life Member
 
"BLOOD MAKES THE GRASS GROW"

Offline shortstroke 91

  • Trad Bowhunter
  • **
  • Posts: 671
Re: ? regarding Ashby FOC
« Reply #7 on: July 02, 2009, 08:55:00 PM »
shortstroke 91
TBOT Life Member
 
"BLOOD MAKES THE GRASS GROW"

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©