Author Topic: why do i keep showing nock high (Read 794 times)

jonesy · « **on:** June 08, 2007, 11:36:00 PM »

I keep showing nock high, not right, nor left nock. shows good spine (shooting woodies), but i cant get arrow to level out, tried everything, is it my release, or i'm i moving nocking point to much? I'ts frusrating.Jonesy

vermonster13 · « **Reply #1 on:** June 08, 2007, 11:41:00 PM »

Are you raising your nock point a little to tune for this?

jonesy · « **Reply #2 on:** June 08, 2007, 11:47:00 PM »

MAN DAVE, IVE BEEN DOING EVERYTHING.

vermonster13 · « **Reply #3 on:** June 08, 2007, 11:48:00 PM »

If hitting high raise the nock point a very little bit at a time. WHere is your nock at now?

jonesy · « **Reply #4 on:** June 08, 2007, 11:51:00 PM »

IVE BEEN LOWERING IT, NOCK IS, WELL WAS 1/2 ABOVE CENTER, BUT IVE BEEN LOWERING IT INSTEAD OF RAISING IT.

vermonster13 · « **Reply #5 on:** June 08, 2007, 11:56:00 PM »

There you go. You need to raise when high

jonesy · « **Reply #6 on:** June 09, 2007, 12:00:00 AM »

THANKS,DAVE!

Full Quiver II · « **Reply #7 on:** June 09, 2007, 12:00:00 AM »

jonesy,

My Black Widow ended up being 5/8 above center and that did it. Took me a while to go above 1/2", as I kept insisting that 5/8 was too high, but when I finaly did, it turned out perfect. Funny, if I went an additional 1/8" above the 5/8" I was WAY Nock High. Go as high as almost 3/4 if you need to. If that does not do it, start over at 3/8. You may be too high and your arrow is bouncing off the shelf (giving you a false "nock high"). Rest easy tonight and try again tomorrow. You'll find the SWEET SPOT!

vermonster13 · « **Reply #8 on:** June 09, 2007, 12:06:00 AM »

FQII is right also, but I bet you started down there.
Only move the nock about 1/32" at a time

jonesy · « **Reply #9 on:** June 09, 2007, 12:07:00 AM »

THANKS TRIPP, I WILL. jonesy

**DONOTDELETE** · « **Reply #10 on:** June 09, 2007, 12:51:00 AM »

What's your FOC on those arrows bro?

and dose it vary with different yardage?

jonesy · « **Reply #11 on:** June 09, 2007, 01:00:00 AM »

Kirk, i was moving the nocking point the wrong way go figure, two ways of doing it and i pick the wrong way lol

**DONOTDELETE** · « **Reply #12 on:** June 09, 2007, 01:15:00 AM »

done the same thing sighting in my 300 sav one time....felt a little silly at the time...but i got over it......follow the arrow yessireee....

bbassi · « **Reply #13 on:** June 09, 2007, 06:53:00 AM »

one other trick if that doesn't work. If your serving is thin or your arrow nocks are sloppy, try a double nock. One above and one below, but not too tight. I've got a couple bows that the arrows tend to slide on the string at release and showing nock high no matter where I had the nock. with 2 nocks I started shooting bullet holes.

Shawn Leonard · « **Reply #14 on:** June 09, 2007, 09:48:00 AM »

If your bareshafting by point of impact and nock is high than lower it. Fore some raeson, I like a real high nock on all my bows. 7/8ths to an inch above center. I believe Bob Morrison also has a high nocking point. I spoke to him a couple times and he thinks it has to do with the way we apply pressure to the arrow. Shawn

Danny Rowan · « **Reply #15 on:** June 09, 2007, 10:33:00 AM »

All of my bows whether longbow or recurve are set at 9/16" above center. I have found that is the perfect heighth for me no matter the bow.

Danny

Stykbo · « **Reply #16 on:** June 09, 2007, 02:24:00 PM »

I agree with what both Shawn and Full quiver ll said

jonesy · « **Reply #17 on:** June 09, 2007, 04:03:00 PM »

Thanks, Fellas!I'am sure i will have more questions,if not i will have it figured out.JONESY

jonesy · « **Reply #18 on:** June 10, 2007, 10:23:00 PM »

Vermonster and the rest of ya realy know your @#$% Thanks! my arrows are flying like you guesed it arrows or darts whatever you choose.Jonesy


LEFT HAND BOWS CLASSIFIEDS	TRAD GANG CLASSIFIEDS ACCESS	RIGHT HAND BOWS CLASSIFIEDS

News:

Author Topic: why do i keep showing nock high (Read 794 times)

Users currently browsing this topic: