3Rivers Archery



The Trad Gang Digital Market













Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters






LEFT HAND BOWS CLASSIFIEDS TRAD GANG CLASSIFIEDS ACCESS RIGHT HAND BOWS CLASSIFIEDS


Author Topic: Waterproofing limb pads?  (Read 297 times)

Offline KentuckyTJ

  • SPONSOR
  • Trad Bowhunter
  • *****
  • Posts: 8651
Waterproofing limb pads?
« on: September 13, 2011, 03:01:00 PM »
I have felt limb pads under limbs on my new bow. Should I waterproof them if planning to hunt in rain?  What to use? Don't want anything to hurt the finish.

Thanks TJ
www.zipperbows.com
The fulfillment of your hunt is determined by the amount of effort you put into it  >>>---->

Offline Fritz

  • Trad Bowhunter
  • **
  • Posts: 1601
Re: Waterproofing limb pads?
« Reply #1 on: September 13, 2011, 03:28:00 PM »
Could probably try some scotchguard or some silicon based spray they use for waterproofing boots. Never done it, but I would think that would work.
God is good, all the time!!!

Offline Bjorn

  • Trad Bowhunter
  • **
  • Posts: 8789
Re: Waterproofing limb pads?
« Reply #2 on: September 13, 2011, 03:38:00 PM »
I'd talk to the bowyer, and be inclined to replace the felt with something different like string wax.

Offline RRock

  • Trad Bowhunter
  • **
  • Posts: 347
Re: Waterproofing limb pads?
« Reply #3 on: September 13, 2011, 04:04:00 PM »
I think Bjorn is on the right track. How about melting some string wax and soaking your felt pads in the melted wax. I think that might work.

Online Over&Under

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 5108
Re: Waterproofing limb pads?
« Reply #4 on: September 13, 2011, 07:22:00 PM »
Tom
I have the same thing, and was wondering about switching out the felt for cork.

Perhaps Bill will chime in.
“Elk (add hogs to the list) are not hard to hit....they're just easy to miss"          :)
TGMM

Offline elkken

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 3922
Re: Waterproofing limb pads?
« Reply #5 on: September 13, 2011, 07:53:00 PM »
Something that worked really well for me for a limb pad was a bicycle tire inner tube. I cut it to length then split it and trace around my riser for limb bolt holes ect. Very quiet and waterproof .... good luck
Sometimes it's better to be lucky than good

TGMM Family of the Bow

Online jess stuart

  • Trad Bowhunter
  • **
  • Posts: 1722
Re: Waterproofing limb pads?
« Reply #6 on: September 13, 2011, 08:34:00 PM »
I have used felt on my limb pads for years with no problems.  I always figured if the finish was good enough on the rest of the riser why not the limb pads.  That said I now put glass on the limb pads and felt on the glass, I think it looks good and helps with noise a bit.

Offline KentuckyTJ

  • SPONSOR
  • Trad Bowhunter
  • *****
  • Posts: 8651
Re: Waterproofing limb pads?
« Reply #7 on: September 13, 2011, 08:57:00 PM »
Jake, Bill told me what to do and I forgot what he said how to waterproof the felt is why I'm asking. He and Tracy are in Wisconsin on a week long hunting trip until Wednesday or so.

Elkken, good idea. That would work well I'd think. I've always liked cork. No worries with water with them.
www.zipperbows.com
The fulfillment of your hunt is determined by the amount of effort you put into it  >>>---->

Offline ron w

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 13849
Re: Waterproofing limb pads?
« Reply #8 on: September 13, 2011, 09:39:00 PM »
I have had 2 bows that had very thin cork that was used for the limb pads..... as waterproof as it gets!
In the beginner's mind there are many possibilities. In the expert's there are few...So the most difficult thing is always to keep your beginner's mind...This is also the real secret of the arts: always be a beginner.  Shunryu Suzuki

Offline Benjy

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 2259
Re: Waterproofing limb pads?
« Reply #9 on: September 13, 2011, 09:41:00 PM »
Tom, I would be glad to call Bill for you tomorrow. I don't mind harrasing him while I am working and he is out goofing off riding all over the country hunting! I'm sure he would do the same to me  :D  

I agree with Jess. I would just take it apart, let it dry out and "oil" up any metal parts before I put it back together.

Let me know if I need to call Bill for you.

Benjy
TGMM Family of the Bow
ZIPPER NITRO 64" LONGBOW 50#@29"
ZIPPER SXT   60" RECURVE 52#@29"
ZIPPER SXT   64" LONGBOW 71#@29"

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©