3Rivers Archery



The Trad Gang Digital Market













Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters






LEFT HAND BOWS CLASSIFIEDS TRAD GANG CLASSIFIEDS ACCESS RIGHT HAND BOWS CLASSIFIEDS


Author Topic: How to test poundage  (Read 339 times)

Offline proprod

  • Trad Bowhunter
  • **
  • Posts: 21
How to test poundage
« on: June 18, 2013, 02:42:00 AM »
I saw an intereting comment about how a bow was marked would probably be correct poundage with fingers vs. being pulled on a test stand with a hook.

From applied physices I can understand a bow being pulled with fingers will require more poundage because the applied load is over a greater surface area than a single pint hook.

However, I am curious what the standard is? And is it applied consistently?
Hoyt Buffalo 45# 62 inch

Offline Piratkey

  • Trad Bowhunter
  • **
  • Posts: 301
Re: How to test poundage
« Reply #1 on: June 18, 2013, 01:04:00 PM »
The standart is the measure with a simple hook but some bowers (like Kirk Lavender at Bigfoot bows) use a "hook" who imitate the fingers.
I think the Kirk methode is lot more accurate,
If a have a short bow,long draw lenght and big hands, the difference can be around 5/6 pounds,it's alot .   :scared:

Offline Prairie Drifter

  • Trad Bowhunter
  • **
  • Posts: 1136
Re: How to test poundage
« Reply #2 on: June 18, 2013, 02:54:00 PM »
So which would weigh more, fingers or the single hook?
Maddog Bows (16)
Rocky Mnt Recurves(2)
Sierra Blanca Bows (2)
Mike B.

Offline Piratkey

  • Trad Bowhunter
  • **
  • Posts: 301
Re: How to test poundage
« Reply #3 on: June 18, 2013, 02:58:00 PM »
Fingers   :readit:

Offline NBK

  • Trad Bowhunter
  • **
  • Posts: 1374
Re: How to test poundage
« Reply #4 on: June 18, 2013, 03:01:00 PM »
Never knew that.  Ya learn something every day.
Mike


"I belong anywhere but in between"

Online pdk25

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 4946
Re: How to test poundage
« Reply #5 on: June 19, 2013, 12:38:00 AM »
Can't imagine it amounts to more than a pound or so for difference for most folks.

Offline Sixby

  • Tradbowhunter
  • Trad Bowhunter
  • *
  • Posts: 2941
Re: How to test poundage
« Reply #6 on: June 19, 2013, 12:48:00 AM »
With the bow I am building right now I figure I have two more lbs to play with compared to the hook. so I am pulling 62 lb. and I want to hit 62 lbs. I know I can fine sand the bow losing 2 lbs and still be 62 lb when I pull it with fingers.
 Bows vary but that is what I have with this one.
Damon Howatts and Martins were notorious for being 4 too 5 lbs heavier pull than what they wrote on the bow. I suspect that they used a hook and did not compensate. If the scale happens to be a bit heavy then it may be even more.
God bless, Steve

Offline Piratkey

  • Trad Bowhunter
  • **
  • Posts: 301
Re: How to test poundage
« Reply #7 on: June 19, 2013, 05:06:00 AM »
Quote
Originally posted by pdk25:
Can't imagine it amounts to more than a pound or so for difference for most folks.
Yes,it's true,usually the difference is around 2 pounds but in some cases it's more,this is depend the bows geometry,the draw lenght,the bow lenght,etc....

Offline proprod

  • Trad Bowhunter
  • **
  • Posts: 21
Re: How to test poundage
« Reply #8 on: June 19, 2013, 12:30:00 PM »
Thanks, Good feedback any idea on how that is calculated into the dynamic spine calculator?
Hoyt Buffalo 45# 62 inch

Offline Piratkey

  • Trad Bowhunter
  • **
  • Posts: 301
Re: How to test poundage
« Reply #9 on: June 19, 2013, 02:13:00 PM »
It's not calculated by the spine calculator and you have to add yourself 2# on the draw weight case,if you want to be more accurate to know you exact draw weight, you can built a "hook " who imitate the fingers and chek the bow weight with.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©