3Rivers Archery



The Trad Gang Digital Market













Contribute to Trad Gang and Access the Classifieds!

Become a Trad Gang Sponsor!

Traditional Archery for Bowhunters






LEFT HAND BOWS CLASSIFIEDS TRAD GANG CLASSIFIEDS ACCESS RIGHT HAND BOWS CLASSIFIEDS


Author Topic: Setting brace height  (Read 375 times)

Offline VA Elite

  • Trad Bowhunter
  • **
  • Posts: 1028
Setting brace height
« on: December 26, 2014, 12:15:00 PM »
So samick sage brace height is recommended 8 1/4 . How do I get that? Twist the string in?
If you profess with your mouth Jesus is Lord and believe in your heart that God raised Him from the dead, you will be saved Romans 10:9

Offline Alexander Traditional

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 3709
Re: Setting brace height
« Reply #1 on: December 26, 2014, 12:23:00 PM »
You have to measure what it is now,and see which way you need to go. When you twist it up you shorten the string and that gives you more brace height.

Offline pinky

  • Trad Bowhunter
  • **
  • Posts: 348
Re: Setting brace height
« Reply #2 on: December 26, 2014, 12:36:00 PM »
Yep.  Not sure where you are starting from?  Leave the top string loop on the top limb and remove the bottom loop from the bottom limb tip.  You can start twisting  6--8--more twists and restring the bow and check again.  More twists in the string equals more brace hight.  Repeat until desired brace height is achieved.  Twist or untwist to get close to your desired brace height.  After shooting a few arrows you will probably need to recheck and adjust.
Martin Hatfeild TD (bearings)RC
Trails End     (Good Medicine) RC
Selway (Lil Shooter) LB
Aspen (Elite) LB

Public Land Hunter

Offline macbow

  • Trad Bowhunter
  • **
  • Posts: 2870
Re: Setting brace height
« Reply #3 on: December 26, 2014, 01:13:00 PM »
How far do you need to move it?
If you have a endless string there is a limited amount of twist.
If a Flemmish twist then you have more room for added twist.

A string that is twisted more than 8 to 10 twist per inch is less desirable.
United Bowhunters of Mo
Comptons
PBS
NRA
VET
"A man shares his Buffalo". Ed Pitchkites

Offline VA Elite

  • Trad Bowhunter
  • **
  • Posts: 1028
Re: Setting brace height
« Reply #4 on: December 26, 2014, 01:42:00 PM »
With factory string it was 7. But Im ordering a fast flight from big jim. So I will have to see the
If you profess with your mouth Jesus is Lord and believe in your heart that God raised Him from the dead, you will be saved Romans 10:9

Offline damascusdave

  • Trad Bowhunter
  • **
  • Posts: 3273
Re: Setting brace height
« Reply #5 on: December 26, 2014, 02:04:00 PM »
No sense even worrying about it until you get the string from Big Jim...twist the one you have now so that it gives you more like an 8 inch brace height...you are not really worried about how well it shoots at this point as you are going to be replacing it...and do not worry much about arrow spine or flight...it will most certainly change with the better string...so do you have someone working with you on your form...tuning without solid form is just an exercise in frustration...I have been shooting for 5 years now, I have tuned a bunch of bows, and some days I just give up on trying to tune something new because my form is off a bit

DDave
I set out a while ago to reduce my herd of 40 bows...And I am finally down to 42

Offline Stump73

  • Trad Bowhunter
  • **
  • Posts: 2852
Re: Setting brace height
« Reply #6 on: December 26, 2014, 02:14:00 PM »
3rivers on their website says  that for the sage the recommended brace height is between 7 1/2 " -   8 1/2". Every bow is different and will have a different brace height. so your not to far from the starting point. You just need to adjust it to fine the sweet spot.
BigJim Thunderchild 54" 52# @ 28"
BigJim Thunderchild 56" 42# @ 28"

Offline VA Elite

  • Trad Bowhunter
  • **
  • Posts: 1028
Re: Setting brace height
« Reply #7 on: December 26, 2014, 03:15:00 PM »
I will get with a few local guys after get string and arrows and see what we can do.
If you profess with your mouth Jesus is Lord and believe in your heart that God raised Him from the dead, you will be saved Romans 10:9

Online katman

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 3574
Re: Setting brace height
« Reply #8 on: December 27, 2014, 07:04:00 PM »
That B-50 stock string will stretch a fair amount, leave it braced and shoot it monitoring brace height.
shoot straight shoot often

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©