Shooters Forum

Contribute to Trad Gang
Become a Trad Gang Sponsor



Author Topic: Bareshafting PSE Sequoia 50#  (Read 1019 times)

Offline Blackhat

  • Trad Bowhunter
  • **
  • Posts: 150
Bareshafting PSE Sequoia 50#
« on: September 12, 2008, 10:04:00 AM »
Was shooting last night at my Walmart target (burlap bag with walmart plastic bags inside),  with fletched and unfletched Easton XX75 Gamegetter 500's, the arrows are 30" with 125 grain field tips.  shooting from the 15  yard  mark.  I would nail the target center with one bare shaft and the next would take a detour about 3 yards from the target.  On these I did get a string slap.  Am I torquing the string?  I'm sure the fault is mine I just can't figure it out.  Any suggestions.
"When Bows shoot faster than 300 fps it ain't called Bowhunting no more!"

Offline Stringdancer

  • Trad Bowhunter
  • **
  • Posts: 245
Re: Bareshafting PSE Sequoia 50#
« Reply #1 on: September 13, 2008, 01:30:00 PM »
You are likely toquring the bow.  Take a loose grip Not a death grip on the bow, and give that a try.  Let the contour of the grip sit in the web of your hand, and keep your fingers from touching the back of the bow. I assume your shooting a Recurve.......

Mike
" FEAR THE MAN WITH ONE BOW "

Offline Blackhat

  • Trad Bowhunter
  • **
  • Posts: 150
Re: Bareshafting PSE Sequoia 50#
« Reply #2 on: September 13, 2008, 05:52:00 PM »
No, it's a 68" longbow reflex/deflex.
"When Bows shoot faster than 300 fps it ain't called Bowhunting no more!"

Offline Stringdancer

  • Trad Bowhunter
  • **
  • Posts: 245
Re: Bareshafting PSE Sequoia 50#
« Reply #3 on: September 14, 2008, 08:10:00 AM »
How tight do the nocks fit on your string?  I know those nocks fit most strings far too tight, and that in itself will cause all kinds of flight problems.  You may want to give the 3-D Super Nock a try if your's are too tight.  I just reserve my strings to get proper nock fit.  This were I would start.  Also, check your brace height.....  I would start at 6.5" and go up from there till you get better results.  Let me know how it goes......
" FEAR THE MAN WITH ONE BOW "

Offline Blackhat

  • Trad Bowhunter
  • **
  • Posts: 150
Re: Bareshafting PSE Sequoia 50#
« Reply #4 on: September 18, 2008, 06:19:00 PM »
I haven't been able to shoot for a couple of days.  Went from a 3 finger shooting glove back to a finger tab.  groups improved at 10 yards.  The bare shafts hit near the spot while the fletched arrows hit more to the right but mostly on a horozintal plane.    :thumbsup:
"When Bows shoot faster than 300 fps it ain't called Bowhunting no more!"

Offline O.L. Adcock

  • Trad Bowhunter
  • **
  • Posts: 823
Re: Bareshafting PSE Sequoia 50#
« Reply #5 on: September 19, 2008, 02:08:00 PM »
"The bare shafts hit near the spot while the fletched arrows hit more to the right"

The fletched arrows are going closer to where "you" are pointing them so that's a form issue. The fact the bare shafts are averaging further to the left of the fletched arrows is a stiff condition. Go up in point weight a couple steps. You won't know what the correct point weight is until the bare shafts start grouping right of the fletched shafts......O.L.
---Six NAA/FITA National and World flight records.----

Offline Blackhat

  • Trad Bowhunter
  • **
  • Posts: 150
Re: Bareshafting PSE Sequoia 50#
« Reply #6 on: September 20, 2008, 10:46:00 AM »
Thanks!  I'll try that today.
"When Bows shoot faster than 300 fps it ain't called Bowhunting no more!"

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©