INFO: Trad Archery for Bowhunters



Author Topic: Need help Identifying a knife maker.  (Read 720 times)

Offline Wyoming Artifact

  • Trad Bowhunter
  • **
  • Posts: 20
Need help Identifying a knife maker.
« on: April 07, 2012, 07:36:00 PM »
Hi guys.  I have enjoyed looking at all the nice work that you all turn out. I don't add much to the conversation but I have learned a lot. I now have a question. I bought a knife not long ago and have not been able to ID the maker. I would like some help if you recognize it could you let me know.I would add a photo but I am yet to figure out that process. The makers mark is a backwards L attached to an R which is attached to a W. So you have a backwards L which is the back of the R and the leg of the R is the left arm of the W. The knife is damascus with a handle similar to Scagal but hard wood was used in place of leather. The knife is said to be about 20 years old. Thanks for the help and I hope it makes sense. Some day when I figure out the photo thing I would like to add a photo of one of my knives but I must say you guys are a little intimidating with the skill you have.
Be Joyful in hope, patient in affliction and faithful in prayer.

Offline Rusty Izatt

  • Trad Bowhunter
  • **
  • Posts: 291
Re: Need help Identifying a knife maker.
« Reply #1 on: April 08, 2012, 08:00:00 PM »
Tim,
If you e-mail me a picture I can post it for you.

Rusty
[email protected]

Offline Wyoming Artifact

  • Trad Bowhunter
  • **
  • Posts: 20
Re: Need help Identifying a knife maker.
« Reply #2 on: April 08, 2012, 08:39:00 PM »
On the way and thank. I will overcome this shortfall with time.
Be Joyful in hope, patient in affliction and faithful in prayer.

Offline Rusty Izatt

  • Trad Bowhunter
  • **
  • Posts: 291
Re: Need help Identifying a knife maker.
« Reply #3 on: April 08, 2012, 10:06:00 PM »
Here are pictures of the knife.
 
 

Offline Pete Crowl

  • Trad Bowhunter
  • **
  • Posts: 37
Re: Need help Identifying a knife maker.
« Reply #4 on: April 09, 2012, 04:38:00 PM »
Could it be an older Ron Welling knife?  He lives in Scagel country.  His middle initial is L.  Just a thought!
Pete Crowl

Blade Show Table 8 R

ABS Journeyman

Offline Wyoming Artifact

  • Trad Bowhunter
  • **
  • Posts: 20
Re: Need help Identifying a knife maker.
« Reply #5 on: April 09, 2012, 08:24:00 PM »
Pete, Thanks for the input. That was a good thought and someone ran that trail but it was not him, The guy I got it from said about 20 years ago knives were given to employees where his dad worked. He said the knives were by a maker in Arkansas. So I contacted the knife maker guild there. He also thought that it might be a Welling knife even though Mr.  Welling does not live in AR. He had to send photos as Mr. Welling does not use high tech. So he and I are about on the same skill level on Computers. Mr. Welling said it was not his. That is as far as I have gotten. There is a lot of experience here on Trad Gang so I thought someone might recognize it. It is obvious an experienced craftsman. Thanks again.
Be Joyful in hope, patient in affliction and faithful in prayer.

Offline Wyoming Artifact

  • Trad Bowhunter
  • **
  • Posts: 20
Re: Need help Identifying a knife maker.
« Reply #6 on: April 20, 2012, 11:30:00 PM »
I picked up a book on Abebooks tha is THE CUSTOM KNIFE II. It was printed in 1974 and list 100 custom makers in the states at that time. This maker is not in there. The hunt continues.   :dunno:
Be Joyful in hope, patient in affliction and faithful in prayer.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©