FLUSH CUT ROUTER BITS

[RAU]

Wheres the best place to get a 2" depth of cut flush cut patternmakers router bit?

[Ricky Wallace]

Have you checked Rocklerwood.com?  They have almost anything,good quality to.

[Misguided One]

Here is the place the company I work for orders bits from. They are a little more expensive than buying them at the big box stores, but they have just about any bit you could possibly need.

 http://www.hartlauer-bits.com/

[mtquivers]

you can get most any router bit here.

 http://www.eagleamerica.com/product/v102-0552b

item# 102-1265B

[Robertfishes]

I use a router table with the #7807 bit, so far so good..   http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/bt_flush.html

[akgator]

An important safety tip: if you are making a new form and drive screws close to the edge where you will be routing, make sure you drive them straight. Just a little contact with a metal screw will absolutely trash a brand new $45 router bit. I won't make that expensive mistake again...

[rbbhunt]

I bought mine at Woodcraft

[Jeremy]

I bought mine from Grizzly

[ChristopherO]

Woodline is less costly and hold up pretty decent.

[beachbowhunter]

Has anyone found a top bearing bit for a 1/4 inch shank that is 1 3/4 or longer?  Seems the 2" ones are all 1/2 " shank.  Dont want to have to buy another router. but might have to. I've done the two pass, but I think the 1/4 inch shank is not stiff enough to keep everything square when it is extended way out.

[Mad Max]

The ones at the big box store are not flush cut, they are made for trimming laminate tops, so it cuts close but not flush. I think I am going to buy a 1/2" router and get the long bit and cut it in one pass.

[beachbowhunter]

I think I might have to do that too.  Pulling the 1" bit so far out gives me the willies and I think it is a bit off square.

[monterey]

I think I might have to do that too.  Pulling the 1" bit so far out gives me the willies and I think it is a bit off square.

i just bought one recently but don't remember where I got it.  But, one inch cut was the longest I could find for a 1/4" shaft.  If you find something longer please post it.  But, the 1/2 router is probably the solution.  Hate to spend the money given that I hardly ever use the router for anything but forms.

[Mad Max]

I agree Monterey but you could always sell it later when you get old---older

[buddyb]

Robert how does the router table work and are you doing one piece longbow forms or takedown forms? I haven't tried it yet I have the same setup.

[Robertfishes]

BuddyB, I have made 2 one piece Recurve forms, a form for a 66" R/D longbow and a ILF limb form using the Router table. I had never touched a Router before making those forms.. I tried to use the 2" bit without the table and it did not go well,very hard to control. So I purchased the table and got it done. I was talking with Steve Jewett a couple of weeks ago and he has made a good number of forms.. It sounds like he routes his forms the same as KennyM, Kenny might have a video or pictures of his process. 

[monterey]

I agree Monterey but you could always sell it later when you get old---older

I ve been missing Roy since he went MIA but you are filling in nicely.

 

[Mad Max]

  

[buddyb]

I tried the freehand router and it didn't work out well for me either. I'll try the table.

thanks.

[Robertfishes]

Buddy,I'll try to tell you how I did it..Didnt get good sleep last night, I have not had to make a new form in 5 years, I am not a wood worker by trade so I have only used the router for bow forms.... First I  Remove as much wood as I can before routing.. I use a 6 ft straight edge to mark a straight line onto form for bottom of template, then screw a template onto form, trace line onto form, remove template, cut about 3/16 from line, using my belt edge sander sand 1/8 inch from line then screw template back onto form and use router table to cut final wood surface. Checking the surface with a good square I mark any divots ( i usually get one) and fill them in with bondo, Then I use 3M High temp 90 spray contact glue to glue a piece of 040 black glass on top of the cut form, Guys like kennym that have great skill with their routers can skip the glass..