Author Topic: 3 pc build along (Read 5840 times)

hera · « **on:** February 16, 2008, 11:22:00 AM »

For those who have never build their own bow,hope your next trophy might well be shot by your own handcrafted bow ,even though I didn't have any outdoor shooting experience .

hera · « **Reply #1 on:** February 16, 2008, 11:40:00 AM »

Rosewood santos = pau ferro.

hera · « **Reply #2 on:** February 16, 2008, 11:42:00 AM »

hera · « **Reply #3 on:** February 16, 2008, 11:55:00 AM »

Jedimaster · « **Reply #4 on:** February 16, 2008, 12:22:00 PM »

Lookout! I think Hera's getting inspired! I hate whatever that was bored a hole in a nice block of wood. I bet you'll figure a way to use it anyway. Love to see your work.

hera · « **Reply #5 on:** February 16, 2008, 12:29:00 PM »

Here is the original design.My favor

hera · « **Reply #6 on:** February 16, 2008, 12:31:00 PM »

Quote

Originally posted by Jedimaster:
Lookout! I think Hera's getting inspired! I hate whatever that was bored a hole in a nice block of wood. I bet you'll figure a way to use it anyway. Love to see your work.

Danny

The wood block I received was defective. It came with a through worm hole. I have to try to use the best of beautiful grain of the wood and avoid the hole at the same time. I think that's what "read wood" means.

hera · « **Reply #7 on:** February 16, 2008, 01:02:00 PM »

I think that worm hole will cut off in window work.( I'm not 100% sure.if not,I can repair that defect)

(( May be that worm hole is a good natural sight bushings hole. LOL))

brettlandon · « **Reply #8 on:** February 16, 2008, 01:52:00 PM »

Hera, you are "reading the wood" in a wise way. That hole will either complement the bow, disappear in the sight window or be covered by the rug and strike plate (maybe an insert on the out side for a quiver). This is a fun build-along. Thanks for posting it!

-Brett

Louutah · « **Reply #9 on:** February 16, 2008, 02:22:00 PM »

Alway look forward to these.....

hera · « **Reply #10 on:** February 16, 2008, 10:46:00 PM »

hera · « **Reply #11 on:** February 17, 2008, 07:58:00 AM »

Angle 1 = angle 2
It's not easy without bandsaw.I have to do it carefully when I cut it by pull saw and sander.

whitebuffalo · « **Reply #12 on:** February 17, 2008, 09:05:00 AM »

Lookin good bud

Chisler · « **Reply #13 on:** February 17, 2008, 10:28:00 AM »

You have my full attention Hera!!

Widowbender · « **Reply #14 on:** February 17, 2008, 11:13:00 AM »

I'll be tuned in again, for sure!!

David

hera · « **Reply #15 on:** February 17, 2008, 11:24:00 AM »

In this picture, original shaft design seem 1" above the deepest grip(correspond to center line),but I prefer 1/2".

hera · « **Reply #16 on:** February 17, 2008, 11:33:00 AM »

hera · « **Reply #17 on:** February 17, 2008, 11:36:00 AM »

hera · « **Reply #18 on:** February 17, 2008, 11:37:00 AM »

Knife eraser !

hera · « **Reply #19 on:** February 17, 2008, 11:50:00 AM »

Why I lower that distance? In my callow opinion,it will get more power and balance if arrow close to the center line.


LEFT HAND BOWS CLASSIFIEDS	TRAD GANG CLASSIFIEDS ACCESS	RIGHT HAND BOWS CLASSIFIEDS

News:

Author Topic: 3 pc build along (Read 5840 times)

Users currently browsing this topic: