Author Topic: air bubbles  (Read 462 times)

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
air bubbles
« on: April 15, 2011, 09:01:00 PM »
What causes air bubbles underneath the glass. I use a press with fire hose @ 65-70 PSI Sometimes I get bubbles and sometimes the limb is perfect, no bubbles. Could it be to much glue? Tony

Offline Lee Robinson .

  • Trad Bowhunter
  • **
  • Posts: 727
Re: air bubbles
« Reply #1 on: April 15, 2011, 09:09:00 PM »
How are you applying it to the laminations?
Until next time...good shooting,
Lee

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Re: air bubbles
« Reply #2 on: April 15, 2011, 09:17:00 PM »
A 1" wide plastic puddy knife.

Online kennym

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 17340
Re: air bubbles
« Reply #3 on: April 15, 2011, 09:24:00 PM »
Hi Tony,

I rarely (not gonna say never)  get any bubbles.

I wonder if it is because I build longbows,and you make TD's? Maybe the bubbles have a bit more time to surface and are eliminated.

I use a wood scrap,like 1/8" x 3/4" x 10" for a spreader.

I'm sure your glue is not cold?

I've been told sliding the lams around a little on each other helps too, but I'm sayin if the air bubbles are in the stack, some of em are gonna stay there.
Stay sharp, Kenny.

   https://www.kennysarchery.com/

Offline Lee Robinson .

  • Trad Bowhunter
  • **
  • Posts: 727
Re: air bubbles
« Reply #4 on: April 15, 2011, 09:26:00 PM »
Do you scrape it in pretty good or just swipe it gently? I put it on one way, and then go back the other way, and then back again...being sure to get it into the pores. I use firm pressure...not gentle and not hard. I have never had air bubbles on my high pressure form, which I use for my Protege Longbows. I did have bubbles once on a kid bow on a inexpensive form that I used "rubber bands" to glue it up, but I didn't use enough rubber straps IMO to put much pressure on it and I believe that was the cause. The bubbles in that kid bow were very minor though.

I would also suggest increasing your hose pressure.
Until next time...good shooting,
Lee

Offline 7 Lakes

  • Trad Bowhunter
  • **
  • Posts: 766
Re: air bubbles
« Reply #5 on: April 15, 2011, 09:45:00 PM »
Try running a hair dryer over the glued  lamination.  It brings bubbles to the surface where they can be wiped off.

Online kennym

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 17340
Re: air bubbles
« Reply #6 on: April 15, 2011, 09:51:00 PM »
Good points guys.

Like Lee, I work it in pretty good.
Stay sharp, Kenny.

   https://www.kennysarchery.com/

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Re: air bubbles
« Reply #7 on: April 15, 2011, 11:13:00 PM »
Thanks guys for your input, I'll try some of your suggestion on the next glue-up. Tony

Offline JamesV

  • Trad Bowhunter
  • **
  • Posts: 2027
Re: air bubbles
« Reply #8 on: April 16, 2011, 08:20:00 PM »
Also when you mix your smooth-on don't whip it just gentle stiring will help to keep bubbles out of the mix. Make sure both surfaces are covered with no dry spots and the glue is worked in. I probably use too much glue but I never have bubbles. When I use clear glass over expensive wood, I hold my breath while pulling the tape off the limbs, it seems to help.

James.....................
Proud supporter of Catch a Dream Foundation
-----------------------------------
When you are having a bad day always remember: Everyone suffers at their own level.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©