« previous next »
Pages: [1]   Go Down

Author Topic: One too many! Bench Vise set up Pg. #2 , Pics !!!!  (Read 637 times)

Offline Osagetree

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 3512
One too many! Bench Vise set up Pg. #2 , Pics !!!!
« on: June 28, 2011, 05:11:00 PM »
This vice has seen one too many osage staves.

Dang, this puts a slight hold up on things!

     :help:    
   
Logged
>>--TGMM--> Family of the Bow

Offline bigcountry

  • Trad Bowhunter
  • **
  • Posts: 1027
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #1 on: June 28, 2011, 05:29:00 PM »
There is something so satisfying with breaking tools from good honest use.

I don't care if its breaking a fishing rod on a big ole fish, or wearing out a gun barrel from shooting it so often, or an old case knife that has been sharpened and used so much there's very little metal left.

Now, it sucks breaking tools because of misuse, carelessness, or just stupidity.
Logged

Offline snag

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6337
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #2 on: June 28, 2011, 05:31:00 PM »
That's too bad. But I think you got your use out of it.
Logged
Isaiah 49:2...he made me a polished arrow and concealed me in his quiver.

Offline George Tsoukalas

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 2922
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #3 on: June 28, 2011, 05:39:00 PM »
I've never seen that happen. Ever.  :)  Jawge
Logged

Offline KellyG

  • Trad Bowhunter
  • **
  • Posts: 4254
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #4 on: June 28, 2011, 06:05:00 PM »
Joe you might be able to use a c clamp to hold the stave on the vise that is still attached to the bench.
But that is a bummer don't know if you can just replace the pieces that snapped or not.
Logged

Offline DVSHUNTER

  • Trad Bowhunter
  • **
  • Posts: 2717
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #5 on: June 28, 2011, 06:16:00 PM »
had that happen to me about two yeaes ago. Bummer man.
Logged
"There is a natural mystic flowing through the air; if you listen carefully now you will hear." Bob Marley

Offline Eric Krewson

  • Trad Bowhunter
  • **
  • Posts: 3126
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #6 on: June 28, 2011, 06:24:00 PM »
If that vise is one of the good old American made ones I am surprised it broke. I broke two Chinese ones before I got off my wallet and bought an American made one, no more problems.
Logged

Offline Stiks-n-Strings

  • Moderator
  • Trad Bowhunter
  • ***
  • Posts: 3226
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #7 on: June 28, 2011, 06:42:00 PM »
Joe sent you a PM
Logged
Striker stinger 58" 55# @ 28
any wood bow I pick off the rack.
 2 Cor. 10:4
 TGMM Family of The Bow
 MK, LLC Shareholder
Proud Member of the Twister Twelve

Offline John Scifres

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 4540
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #8 on: June 28, 2011, 08:44:00 PM »
If you used power tools that wouldn't have happened  :)   I gotta spare if you need it but I bet shipping would cost more than a garage sale vise.

You might get with Wilton and see about the lifetime warranty:   http://www.wiltontools.com/us/manufacturing/en/wilton/product.html?node=4546&product=273830
Logged
Take a kid hunting!

TGMM Family of the Bow

Offline va

  • Trad Bowhunter
  • **
  • Posts: 194
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #9 on: June 29, 2011, 10:39:00 AM »
Hey Eric -

"got off my wallet" HA

I am going to use that one.

va
Logged
Poor folk with poor ways, but rich just the same.

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #10 on: June 29, 2011, 11:25:00 AM »
Joe, I broke 3 of those little red vices over the years. They all broke trying to hog off the bark and sapwood on osage staves. I finally bought a bigger, heavier vice(this one is gray) from Lowe's and haven't looked back!  I'm sure the color makes the difference! d;^)
Logged
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline SEMO_HUNTER

  • Trad Bowhunter
  • **
  • Posts: 2792
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #11 on: June 29, 2011, 02:24:00 PM »
Does any place carry that size threaded rod? You might be able to replace it if you could find the same size thread.

But all I can say is you need to stop working so hard Joe. Give your poor old vice a break once in awhile.   :goldtooth:
Logged
~Varitas Vos Liberabit~ John 8:32

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #12 on: June 29, 2011, 03:05:00 PM »
That's the problem Semo. Joe did give that vise a break! d;^)
Logged
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline snag

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6337
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #13 on: June 29, 2011, 05:47:00 PM »
Better the vise than the bow breaking.
Logged
Isaiah 49:2...he made me a polished arrow and concealed me in his quiver.

Offline George Tsoukalas

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 2922
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #14 on: June 30, 2011, 08:29:00 AM »
I use a woodworker's vise to hold the stave and a strap if needed. Jawge
 http://georgeandjoni.home.comcast.net/~georgeandjoni/bowbench.html
Logged

Offline Osagetree

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 3512
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #15 on: July 04, 2011, 02:24:00 PM »
Thanks to all those that offered help and advice!!

Never thought about a warranty,,, good idea John.

But I went to the flea market and found another one for 15 bucks. It's a "Pony"......

 

So,,, I'll rig it up like the old one.

Remove the original metal grip plates and replace them with some leather that wont mar the wood as bad.
The original plates fit in an off set atop the jaws of the vise. Cut the 1st peice of leather to fit and fill the off set on the jaws of the vise. The original screws are used to hold the leather fill peices in place.

 
 

Then, I cut two more leather pieces to cover the screw heads and to provide the jaws of the vise a bit of a softer grip for wood work.
To glue the two final peices to the leather already mounted on the jaws, I use  a glue that remains pliable when cured. This "lock-tite, no mess" stuff works well.

 
 

A little grease on the screw.

 

Line everything where ya want it and clamp down a piece of osage slat until the glue dries.

 

Now I'm in like Earl Flynn!

 
Logged
>>--TGMM--> Family of the Bow

Offline adeeden

  • Trad Bowhunter
  • **
  • Posts: 1786
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #16 on: July 04, 2011, 04:42:00 PM »
Very nice set up Joe!
Logged
"I would rather be lucky then good, any day!"

Offline KellyG

  • Trad Bowhunter
  • **
  • Posts: 4254
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #17 on: July 04, 2011, 06:08:00 PM »
ok now your back in the saddle
Logged

Offline fish n chicks

  • Trad Bowhunter
  • **
  • Posts: 668
Re: One too many! Bench Vise set up Pg. #2 , Pics !!!!
« Reply #18 on: July 05, 2011, 11:41:00 AM »
Never thought of the leather idea. Thanks!
Logged
Pages: [1]   Go Up
« previous next »

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©