Clamps for BBO ????

[Canadabowyer]

Am going to try a BBO and am wondering. Can I use spring clamps instead of C-clamps as long as they are strong ones.I will be using Smooth-on.Going to the big smoke Saturday to buy clamps.    Bob

[Mike Mecredy]

I like to hold them in place with a few of either spring clamps or c clamps, in the center and the tips but then, wrap the whole length of the limbs with strips of rubber inner tubes as tight as I can.

[Echatham]

I used a couple of quick clamps and a bunch of 99 cent from home depot spring clamps on my BBI build here:  http://tradgang.com/noncgi/ultimatebb.php?ubb=get_topic;f=125;t=009703;p=7

worked great... my glue lines are very thin. I think i used 26 spring clamps and 4 quick clamps in total.

[Echatham]

I think most people usually reccomend leaving the smooth on for glass bows, and use either unibond 800 ot TB3 for boo to wood or wood to wood. I used unibond and it was excellent... and not to expensive.

[bowhntineverythingnh03743]

Unibond 800 works best because of its gap filling capabilities. I use c clamps for best results and crank em down good and tight. Great glue lines doing it this way .... Jmo

[Bowjunkie]

I use Smooth On and c-clamps. Smooth On has excellent gap filling properties as well.

[EASTERNARCHER]

For BBO I wrap the lams in shrink wrap to hold everything in place and to minimize glue running all over...Then I wrap the entire thing in inner tube stretched tight....paper thin glue lines, and no boogers to clean up.
Oh ya, I also lay painters tape or packing taper on the back of the boo first to keep the glue from setting on the back. it minimizes trying to clean up excess hardened glue fron the boo backing.

[razorback]

I hear about a lot of people wrapping their bows in plastic wraps of some kind to keep clean up down to a minimum. Doesn't the plastic stick to the glue and need to be cleaned up. How do you prevent/deal with this.

[macbow]

The plastic wrap doesn't stick to the glue too bad.
Just a matter of ripping it off.
I use it every time.

[Roy from Pa]

I use all c clamps, remember to pad the boo with something so the clamps don't indent it. The glue doesn't stick to the plastic. I just snug down the clamps, it doesn't take a lot of pressure when gluing two flat surfaces together 1 1/2 wide.
 

[macbow]

I moved from all clamps some time ago to less clamps and the inner tube rubber.

 

Picture is pretty cluttered but shows the ratio of clamps to inner tube. I use bicycle inner,tubes cut up.
Main clamps are at the center and where the spacer blocks are located.
Small c clamps for the area around the power lamination if used.

[Roy from Pa]

Ron, if you set your beer down, your never gonna find it:)

[LittleBen]

I've used spring clamps. The 99c metal ones from HD. I have a bunch.

I think the c-clamps are probably better becasue you can adjust the clamping force more easily. They're just alot more expensive. maybe $3-5 each or something.

If you don't have either, I'd probably try and find a bulk pack of like 20 c-clamps

[macbow]

Your right Roy. Key is to never set it down.

[Roy from Pa]

Ah I see now. No wonder I sometimes have 2 or 3 open at once..  

[Bowjunkie]

That's not why.

[Roy from Pa]

Well why isn't it why?

[LittleBen]

I'm under strict orders from Dana not to drink more than 1 beer in a day. I can get away with 2, but not the 8 I'd like to have.

[Roy from Pa]

ROK-ROH:)

[Draffish]

you need a camel back roy just fill her up put it on your back and drink