Author Topic: Takedown recurve build along (All Done) (Read 8381 times)

BrushWolf · « **on:** September 11, 2013, 11:06:00 AM »

I have had extra time on my hands. So I thought I would try to do a build along. So here goes. I will be attempting to make a 62" bow out of Claro walnut and curly Koa. The first thing I am going to do is cut out some riser parts.

BrushWolf · « **Reply #1 on:** September 11, 2013, 11:09:00 AM »

Here is the walnut.

BrushWolf · « **Reply #2 on:** September 11, 2013, 11:12:00 AM »

.

.

Once the block was cut out square I cut the profile for the flare.

BrushWolf · « **Reply #3 on:** September 11, 2013, 11:23:00 AM »

Time to move on to the Koa.

BrushWolf · « **Reply #4 on:** September 11, 2013, 11:29:00 AM »

The first cut in the Koa.

beachbowhunter · « **Reply #5 on:** September 11, 2013, 01:17:00 PM »

Wow, freehanding those cuts would be a bear for me. I would never get them to fit!

MoeM · « **Reply #6 on:** September 11, 2013, 02:30:00 PM »

X².... really handy!

takefive · « **Reply #7 on:** September 11, 2013, 05:13:00 PM »

That is some beautiful wood

BrushWolf · « **Reply #8 on:** September 11, 2013, 09:26:00 PM »

After those two cut its time to fit them together.

I am not good enough with the saw for them to fit . So I have to sand them with a drum. The sanding drum has a stop on it and
I use a pattern to get every thing exact.

Dmaxshawn · « **Reply #9 on:** September 11, 2013, 09:31:00 PM »

Looking good bud. Love my brushwolf.

JJB · « **Reply #10 on:** September 11, 2013, 09:42:00 PM »

That's going to look sharp, looking forward to following along.
-Jay

LittleBen · « **Reply #11 on:** September 12, 2013, 09:37:00 AM »

Very nice! I love claro walnut ... very nice.

David Flanrey · « **Reply #12 on:** September 12, 2013, 09:57:00 AM »

Keep it coming!! Looking very nice.

chackworth3 · « **Reply #13 on:** September 12, 2013, 11:12:00 AM »

Very nice! Love the wood combo!

BrushWolf · « **Reply #14 on:** September 12, 2013, 12:19:00 PM »

The first joint is ready . Now to move to the other one.

beachbowhunter · « **Reply #15 on:** September 12, 2013, 12:19:00 PM »

Can you show the sander stop and pattern set up?

BrushWolf · « **Reply #16 on:** September 12, 2013, 12:23:00 PM »

For the next joint I just start over by cutting out the shape. Then sand to the line using the other half of the pattern.

BrushWolf · « **Reply #17 on:** September 12, 2013, 12:27:00 PM »

Quote

Originally posted by beachbowhunter:
Can you show the sander stop and pattern set up?

I will get a pic or two put on as soon as I can. The drum I use is 2x3 with 36 grit paper. It seems to do the best job for me .

BrushWolf · « **Reply #18 on:** September 12, 2013, 02:39:00 PM »

Here is the drum. The black wheel on the bottom is what I call a stop.

BrushWolf · « **Reply #19 on:** September 12, 2013, 02:48:00 PM »

As for the patterns they are 1/2" plywood. Each one has a center line to keep everything straight. They also have makes to tell me were the lines for the joint is going to be. I line all the marks up an two face tape the pattern down. The pattern usually set around 1/16 back from the edge to allow every thing to clean up.

It definitely took me sometime to get the patterns to fit up before they were ready to be used.

News:

Author Topic: Takedown recurve build along (All Done) (Read 8381 times)

Users currently browsing this topic: