Author Topic: Designing the ultimate wooden bow - revisited 8 yrs later  (Read 703 times)

Offline onemississipp

  • Trad Bowhunter
  • **
  • Posts: 668
Designing the ultimate wooden bow - revisited 8 yrs later
« on: November 11, 2013, 08:34:00 AM »
Back in 2005, bowyers were asked about what their ultimate wooden bow would be. Let's hear from those that participated and changes if any!

2005 link

  http://tradgang.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=40;t=000051;p=1
Dustin
_ _ _________________________________ _  _

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20689
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #1 on: November 11, 2013, 09:31:00 AM »
I really miss Mickey...

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #2 on: November 11, 2013, 09:43:00 AM »
"OK Mickey, Here goes....
Osage, 62"-66"T/T, bulbous handle,rigid to simi-bending,4" handle, 1 1/2"-2" fades,either straight taper or full out to 6" then taper to 3/8"tips,1 3/8"-1 1/2" at fades,asymetrical (but lately I've been trying symetrical, slightly rounded belly, air backing, no arrow rest or small glued leather rest,usually overlays(bone,antler,hardwood),Tru-Oil, straight or slightly reflexed(to start with),Rattan wrap or leather handle wrap, and a B-50 Flemish string.
Just a good old stick bow!!! Pat

ps. I use the same bow for everything!"

  That is what I wrote in 2005. I've changed a little but not much.
Still osage, now 60" to 66", limbs bend into the handle at full draw. I use a floppy rest along with cordage wrapped handle, I like overlays although they are mostly for cosmetic purposes. I have started also using leather saturated with super glue for tip overlays. All of my bows these days are symetrical with the middle of the bulbous handle the mid point of the bow. I've been building more recurves lately but in this case I'd stick with a straight limbed bow with slight reflex. And I'm still happy with B-50 and a Flemish twist string.
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline onemississipp

  • Trad Bowhunter
  • **
  • Posts: 668
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #3 on: November 11, 2013, 09:53:00 AM »
I hear ya Roy....there are a few in that forum that are missed.
Dustin
_ _ _________________________________ _  _

Offline onemississipp

  • Trad Bowhunter
  • **
  • Posts: 668
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #4 on: November 11, 2013, 09:57:00 AM »
That's pretty amazing Pat,  I have a suspicion there will not be many changes from most.
Dustin
_ _ _________________________________ _  _

Offline Bowjunkie

  • Trad Bowhunter
  • **
  • Posts: 2324
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #5 on: November 11, 2013, 10:29:00 AM »
I miss a bunch of them guys.

My answers, on page 4 of that thread  haven't changed... except now I'd use Thunderbird instead of Fullerplast.

Though I have made and shot many since, the bow I have pictured in that thread is still my #1 hunting and target bow today. We have history :^), it's 9 years old now, and still stands quite straight unstrung after many thousands of arrows shot.

Thanks for the trip down memory lane.

Offline John Scifres

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 4540
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #6 on: November 11, 2013, 10:32:00 AM »
Here's what I wrote in 2005:

(1) material - osage
(2) 66" NTN (I have a 27" draw)
(3) handle design: rigid
(4) handle length: 3.5"
(5) fade length: 1.5"
(6) limb design: full width to 8" past fades - approx 1/3 of working limb
(7) limb width at fade: 1.5"
(8) Limb length: top limb is 1.5" longer than bottom
(9)Belly type: rounded flat belly
(10) backing: air
(11)rest type: floppy
(12)overlays: no
(13)profile: straight, turned tips
(14)finish: polyurethane
(15)handle covering: leather wrapped
(16) string type: B-50 flemish

Here's where I have "progressed". Basically shorter with a flat belly:

(1) material - osage
(2) 62" NTN (I have a 27" draw)
(3) handle design: rigid
(4) handle length: 3.5"
(5) fade length: 1.5"
(6) limb design: full width to 8" past fades - approx 1/3 of working limb
(7) limb width at fade: 1.5"
(8) Limb length: fulcrum is at center of bow.  Limbs are equal length from fulcrum.  Lower limb has more of the handle in it than the upper.  i.e. it has more rigid handle in it.
(9)Belly type: flat belly
(10) backing: air
(11)rest type: glued on leather wedge
(12)overlays: no
(13)profile: straight, flipped tips
(14)finish: polyurethane
(15)handle covering: leather wrapped
(16) string type: B-50 flemish
Take a kid hunting!

TGMM Family of the Bow

Offline Black Mockingbird

  • Trad Bowhunter
  • **
  • Posts: 342
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #7 on: November 11, 2013, 11:09:00 AM »
Whewwee!!!! That's a tough question to answer and needs some serious thinking...I'm in the well over a hundred bows made club of all kinds of differing designs and woods,and I still can't come up with a quick answer..except its gonna be osage without a doubt,and that I can answer in a heartbeat..that hasn't changed in years for me and never will....gimme a second..or two..or three etc.....lol.

Offline PEARL DRUMS

  • Trad Bowhunter
  • **
  • Posts: 3457
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #8 on: November 11, 2013, 11:43:00 AM »
64-66" osage flat bow for me.

Offline 2treks

  • Trad Bowhunter
  • **
  • Posts: 5193
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #9 on: November 11, 2013, 05:13:00 PM »
Man Chris, That surprised me. I thought you liked a tad shorter. Hard to beat that bow right there tho.
I would have to stretch the length a bit for my draw length, but yes, Osage Flatbow.
Or,
A nice ELB made of.....
C.A.Deshler
United States Navy.
1986-1990


"Our greatest fear should not be of failure but of succeeding at things in life that don't really matter.”
~ Francis Chan

Online Pat B

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 15027
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #10 on: November 11, 2013, 11:37:00 PM »
This is the original criteria from Mickie..."YOU ARE BUILDING FOR YOURSELF, THE ONLY BOW YOU WILL HAVE TO HUNT WITH FOR THE NEXT 5 YEARS"
...so durability should be at the top of the list. A long, slightly overbuilt flat bow of osage would fit into that category.
Make the most of all that comes and the least of all that goes!
TGMM Family of the Bow

Offline PEARL DRUMS

  • Trad Bowhunter
  • **
  • Posts: 3457
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #11 on: November 12, 2013, 08:31:00 AM »
Chuck most of my bows fall into that range. Even the statics are all in there. I have kept a few 50 something's as well, but most are going to be 64-66".

Offline The Gopher

  • Moderator
  • Trad Bowhunter
  • ***
  • Posts: 304
Re: Designing the ultimate wooden bow - revisited 8 yrs later
« Reply #12 on: November 13, 2013, 04:35:00 PM »
The more things change the more they stay the same!
"The future is, of all things, the thing least like eternity. It is the most temporal part of time, for the past is frozen and no longer flows, and the present is all lit up with eternal rays." ~C.S. Lewis

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©