Author Topic: Floppy Limbs?  (Read 508 times)

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Floppy Limbs?
« on: December 20, 2013, 04:11:00 PM »
I run into this problem every time I try to do a light poundage bow, 30-40 pounds. The limbs are so limber that you can shake the bow and the limbs flop, yet it's probably close to 50#. I think I know what the problem is but would like your input please. I have a stack of .227, 1 piece of .043 clear ULS, 1 pc .050 clear ULS, 2 .030 veneers and a .002 taper, .074. Thanks Tony

Offline Mike Most

  • Trad Bowhunter
  • **
  • Posts: 927
Re: Floppy Limbs?
« Reply #1 on: December 20, 2013, 04:45:00 PM »
Recurve? or longbow?
"It Shall be Life" (Ten Bears to Josie Wales)
------------------                Michael Most-Adkins Texas

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Re: Floppy Limbs?
« Reply #2 on: December 20, 2013, 04:47:00 PM »
60" recurve.

Offline arrowlauncherdj

  • Trad Bowhunter
  • **
  • Posts: 382
Re: Floppy Limbs?
« Reply #3 on: December 20, 2013, 07:22:00 PM »
I myself have found a difference in core material can influence that a bit. I won't Use anything but maple for my lighter bows and I'd put the thicker glass on the belly for extra stability. You might to shallow the pad angle a bit to stiffen the preload.

Dave

Offline bamboo

  • Trad Bowhunter
  • **
  • Posts: 1161
Re: Floppy Limbs?
« Reply #4 on: December 20, 2013, 07:37:00 PM »
how wide?
whats your limb profile look like?
how far out from the fades do you start the side taper and how close to the hook?
Mike

Online Crooked Stic

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6076
Re: Floppy Limbs?
« Reply #5 on: December 21, 2013, 07:21:00 AM »
My recurve had the same problem-floppy limbs. It had a .002 taper. Pretty common in recurves. I redesigned the limb to have a bit more hook and tried a parallel limb but ended up liking .001 taper the best. So what you have got is not enough preload.Strung and unstrung pics would be nice for more comments to give you more help.
High on Archery.

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Re: Floppy Limbs?
« Reply #6 on: December 22, 2013, 03:18:00 PM »
I have discarded those limbs, but I was thinking that a .001 taper would help with my problem. Any suggestions on a stack for a 40# three piece take down recurve. 60"AMO, 15" riser with 27" x 1.6" wide limbs.

Offline wakolbinger

  • Trad Bowhunter
  • **
  • Posts: 155
Re: Floppy Limbs?
« Reply #7 on: December 22, 2013, 03:25:00 PM »
Grind up a little blue pill and mix it in with the
epoxy?

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20689
Re: Floppy Limbs?
« Reply #8 on: December 22, 2013, 03:29:00 PM »
LOL

Offline Buemaker

  • Trad Bowhunter
  • **
  • Posts: 3116
Re: Floppy Limbs?
« Reply #9 on: December 22, 2013, 03:30:00 PM »
Good grief,no no, send the blue pills to me. Bue--.    ;)

Offline arrowlauncherdj

  • Trad Bowhunter
  • **
  • Posts: 382
Re: Floppy Limbs?
« Reply #10 on: December 22, 2013, 04:27:00 PM »
On my curve design going down .001 in the taper rate only inc my poundage by 6-7 lbs. I'd think you'd do ok with a .220 stack.

Dave

Offline Sharp Shooter

  • Trad Bowhunter
  • **
  • Posts: 361
Re: Floppy Limbs?
« Reply #11 on: December 22, 2013, 08:10:00 PM »
HAHAHA guys, I don't need to waste one on a set of limbs! Dave using the .001 taper is what I was thinking. I'm going to try the .220 attack as well. Thanks Tony

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20689
Re: Floppy Limbs?
« Reply #12 on: December 22, 2013, 09:39:00 PM »
Good grief,no no, send the blue pills to me. Bue--. [Wink]

Bue, you would shoot your eye out...   :laughing:

Offline EHK

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 286
Re: Floppy Limbs?
« Reply #13 on: December 23, 2013, 05:12:00 PM »
Wasn't there a post on here about a viagra bow recently?  Funny, there was no blue in that bow anywhere.

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©