« previous next »
Pages: [1]   Go Down

Author Topic: What is your method for applying clear coat?  (Read 490 times)

Offline woodystyle777

  • Trad Bowhunter
  • **
  • Posts: 10
What is your method for applying clear coat?
« on: January 09, 2014, 08:08:00 PM »
Hey guys! About to make my first set of arrows and was curious about the finishing stage.

I watched Raptor Archery's video on Arrow Making and he completely submerged the shafts into clear coat, and then hung them up letting them drip dry.

Is this better than using a dip tube with a squeegee?  Seems like his method would keep more of the clear coat on than squeegeeing a lot of it off?

What is your method for the clear coat stage?
Logged

Offline Bowjunkie

  • Trad Bowhunter
  • **
  • Posts: 2324
Re: What is your method for applying clear coat?
« Reply #1 on: January 09, 2014, 08:41:00 PM »
Wipe on regular gloss Minwax poly. Dries super fast, easy, cheap, available everywhere, no tubes and junk sitting around..... it actually dries a nice satin when wiped on too.
Logged

Offline woodystyle777

  • Trad Bowhunter
  • **
  • Posts: 10
Re: What is your method for applying clear coat?
« Reply #2 on: January 09, 2014, 08:58:00 PM »
how many coats and how long does it take to dry between coats?
Logged

Offline darin putman

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 479
Re: What is your method for applying clear coat?
« Reply #3 on: January 09, 2014, 10:13:00 PM »
I love the massey finish, I use denatured alcohol instead of acetone. 5 or 6 coats for my arrows, mix, wipe on 8 hours later another coat, extremely durable finish!!
Logged
Osage selfbow and Surewood shafts

Offline bigbob2

  • Trad Bowhunter
  • **
  • Posts: 2160
Re: What is your method for applying clear coat?
« Reply #4 on: January 13, 2014, 02:47:00 AM »
would an airbrush with .5mm nozzle be capable of spraying marine spar varnish or would I need a bigger jet? I know nothing about airbrushes which shouldn't be too hard to realise.
Logged

Offline EHK

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 286
Re: What is your method for applying clear coat?
« Reply #5 on: January 16, 2014, 03:10:00 PM »
For arrows, I like to dip in PVC tubes full of minwax polycrylic.  It dries pretty fast and has little if any odor at all.  Thin it down till it runs off the shafts like water and one can of poly will go a very long way.
Logged

Offline Brock

  • Trad Bowhunter
  • **
  • Posts: 1445
Re: What is your method for applying clear coat?
« Reply #6 on: January 16, 2014, 03:28:00 PM »
I dont like a high gloss on anything I am going to hunt with....

on my arrows after I am done staining them...I wipe them down with steel wool to smooth them.  Then I put a coat of water based wipe-on poly from MinWax on the entire shaft...put in my holder and let dry.  I will do 4-6 coats...lightly rubbing with steel wool or scotchbrite pad in between dry coats to knock off any imperfections or dust that settled in finish.

they come out with a mild matte/satin finish...but are sealed pretty good against moisture.
Logged
Keep em sharp,

Ron Herman
Compton's Traditional Bowhunters
Backcountry Hunters & Anglers
PBS Assoc since 1988
NRA Life
USAF Retired (1984-2004)

Offline Dmaxshawn

  • Trad Bowhunter
  • **
  • Posts: 1708
Re: What is your method for applying clear coat?
« Reply #7 on: January 16, 2014, 03:39:00 PM »
Big Jims Buffalo Hide with a pre-val sprayer.  three-four coats gloss then barnish it and spray on three-four coats of satin in a matte finish
Logged
Pages: [1]   Go Up
« previous next »

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©