Author Topic: 2019 what did ya do today.... (Read 196287 times)

Forwardhandle · « **Reply #1060 on:** June 01, 2019, 05:34:21 AM »

That one turned out beautiful Bob glad your getting the bugs worked out that riser wood has very cool grain !

bigbob2 · « **Reply #1061 on:** June 01, 2019, 05:40:46 AM »

Thanks Ritchie. I will have to make a few changes to my form mainly to keep every thing aligned properly but love these bows . 40# is a bit light for my preference but because I Will only be target popping it will be ok, Glad I put those wedges and power lam in too.

Roy from Pa · « **Reply #1062 on:** June 01, 2019, 06:31:59 AM »

That turned out very nice, Bobby..

bigbob2 · « **Reply #1063 on:** June 01, 2019, 06:34:51 AM »

Thanks buddy, sorry to hear of your loss too mate. Take care.

Roy from Pa · « **Reply #1064 on:** June 01, 2019, 06:47:43 AM »

Thanks.

Shredd · « **Reply #1065 on:** June 01, 2019, 07:22:08 AM »

Nice looking lines on the bow, Bob... Do you have a full draw shot also??

bigbob2 · « **Reply #1066 on:** June 01, 2019, 07:32:02 AM »

Sorry Shred, got no one here to take the full draw shot anymore.

Roy from Pa · « **Reply #1067 on:** June 01, 2019, 08:13:33 AM »

Ya have a timer setting on your camera?

It delays taking the picture after ya click the button.

bigbob2 · « **Reply #1068 on:** June 01, 2019, 08:17:34 AM »

Don’t know Roy would have to check it out and it’s bed time here almost 10.15pm. It is only a “ point and shoot” camera

kennym · « **Reply #1069 on:** June 01, 2019, 09:27:39 AM »

That's a sweet one Mr. Bob!!

I spent most of day yesterday getting to my skid loader after the water went down off hwy 36 (4 lane btw) and getting all the water out of it. It got flooded, luckily it only got in the engine and not the hydraulic reservoir or fuel.

Dropped the oil and water out of it and put in a mix of diesel, tranny fluid and engine oil . Believe it or not(I still don't hardly) it cranked right up. Ran it about a minute driving it out of the mud it was in , changed the oil again in engine and the chain cases , and moved it farther uphill. Never assume the water won't get that high because you might get the torrential rains we've had lately...

Pat B · « **Reply #1070 on:** June 01, 2019, 11:31:47 AM »

You may need to run it a little longer, Kenny, at least until it comes to operating temps to be sure all the water and moisture is out. Lots of water coming down through the middle of the country.

kennym · « **Reply #1071 on:** June 01, 2019, 12:06:47 PM »

Yep, I'm gonna run it an hour when I bring it home and change oil again...

Crooked Stic · « **Reply #1072 on:** June 01, 2019, 12:08:44 PM »

Wow Bob very nice. Got this one done yesterday.47@26 50in.

Sent from my SM-J737V using Tapatalk

Fishinglink · « **Reply #1073 on:** June 01, 2019, 12:18:17 PM »

Wow mike. Good job.

Sent from my iPhone using Tapatalk

monterey · « **Reply #1074 on:** June 01, 2019, 12:25:20 PM »

I like that riser wood and it goes nice with the lams too. Is that a custom limb bolt wrench?

Roy from Pa · « **Reply #1075 on:** June 01, 2019, 12:27:01 PM »

Not too bad there pops...

Crooked Stic · « **Reply #1076 on:** June 01, 2019, 12:33:16 PM »

Sight window cut out for the limb wrench. drilled a hole in it and routed for the 90 degree part with a dremel tool filled it with smooth on and put a cover on it.

kennym · « **Reply #1077 on:** June 01, 2019, 12:35:41 PM »

Thought it was a combo wrench/stabilizer.

monterey · « **Reply #1078 on:** June 01, 2019, 12:37:39 PM »

Yeah, if it was me I'd end up shooting the bow with the wrench stuck in the bolt!

Roy from Pa · « **Reply #1079 on:** June 01, 2019, 12:39:33 PM »

I thought it was an old timer assist gadget.

News:

Author Topic: 2019 what did ya do today.... (Read 196287 times)

Shredd

Users currently browsing this topic: