Author Topic: 2019 what did ya do today.... (Read 196662 times)

Crooked Stic · « **Reply #1680 on:** October 09, 2019, 04:52:33 PM »

Went with the FHLB FOR A LITE WEIGHT kid bow

Sent from my LM-X410.F using Tapatalk

Forwardhandle · « **Reply #1681 on:** October 09, 2019, 05:00:35 PM »

Awsome looking riser Mike

Buemaker · « **Reply #1682 on:** October 09, 2019, 05:01:46 PM »

Nice riser.

Roy from Pa · « **Reply #1683 on:** October 09, 2019, 05:14:01 PM »

I guess it's ok:)

Mad Max · « **Reply #1684 on:** October 09, 2019, 06:10:50 PM »

Looks nice stic
how long is that riser?
and Roy said I suppose it's ok verses I guess it's ok

Crooked Stic · « **Reply #1685 on:** October 09, 2019, 06:45:17 PM »

Well thanks an you to Roy. Dont know about you guys but thelast sheet sandpaper I got from Supergrit was junk. So thos stuff more $$ but lasts about. 10 times as long and cuts much better.

Sent from my LM-X410.F using Tapatalk

Crooked Stic · « **Reply #1686 on:** October 09, 2019, 06:47:31 PM »

It is 16 in. Bow is 20@20 58 in.

Sent from my LM-X410.F using Tapatalk

Crooked Stic · « **Reply #1687 on:** October 09, 2019, 06:48:07 PM »

And elRoy may be confused

Sent from my LM-X410.F using Tapatalk

Flem · « **Reply #1688 on:** October 09, 2019, 08:30:16 PM »

Don't know about Supergrit, but I agree with you Stic, 3M sandpaper is the best. My local lumber yard used to sell 3M, but for some reason switched to Gator Grit, which is total crap. Now I have to mail order sandpaper sheets!

Forwardhandle · « **Reply #1689 on:** October 10, 2019, 04:17:18 AM »

Yep 3m for me I use it for my belt sander, last much longer ,really one of those cases you get what you pay for !

Mad Max · « **Reply #1690 on:** October 10, 2019, 06:47:36 AM »

I buy belts from them, but I get the 3M sheets from the big box store

kennym · « **Reply #1691 on:** October 10, 2019, 06:59:16 AM »

I just ordered some zirc belts for my 6x80 from the auction site , Red Label brand I think. Green belts and for metal I think but last a long time on there...

Roy from Pa · « **Reply #1692 on:** October 10, 2019, 07:03:39 AM »

S-Grit sells 3M sheets also.

Bob D · « **Reply #1693 on:** October 10, 2019, 09:23:32 AM »

Today I put a few final details on a 17 inch riser I made from a pc of walnut leftover from a gunstock blank. Its not a very dense pc of wood and does have some flex to it. But it only supports 25 lbs Sage limbs. That’s about all I can shoot due to shoulder problems.
It all went fine until the finish was put on. I had “preserved” some opened Truoil by storing the bottle in a larger glass jar filled with an oxygen blocker. It looked good; no jelling or film. Unknown to me the drying agents had “escaped” and what should have taken a week took months.
I’m calling it done. It shoots good but does need a bit more tuning.

Flem · « **Reply #1694 on:** October 10, 2019, 10:29:21 AM »

Nice Bob! Thats a beautiful chunk of Walnut

Bob D · « **Reply #1695 on:** October 10, 2019, 10:57:28 AM »

Thanks Flem.
It actually has some nice “rainbow” colored mineral streaks in it the camera did not pick up.
I hope it holds up. Its my first riser so I’m already planning what I would do different on the next one. Like I was told, this is addictive.

Roy from Pa · « **Reply #1696 on:** October 10, 2019, 11:22:14 AM »

Very nice, Bob.

Crooked Stic · « **Reply #1697 on:** October 10, 2019, 11:32:35 AM »

Nice poor mans ebony.

oldfartfarmer · « **Reply #1698 on:** October 10, 2019, 02:24:45 PM »

Got 2 pieces of 1.5X1/16 aluminum strips, and an inner tube today,

Going to glue 1 strip on the Form full length and drill for the dowel-stop ----good idea? Bad Idea?

2cd strip ill glue a lamp cord down the center and cut an inch longer than my bow pieces--right?

thanks
John
,

oldfartfarmer · « **Reply #1699 on:** October 10, 2019, 02:32:08 PM »

should i sand the aluminum with 600 or 800 grit ? before using?
,
will the EA-40 glue the bottom aluminum piece to the form if i use it? or should i go with regular store bought epoxy?
,
can I whipe the aluminum with carnauba wax before the glue up?

thanks
john

News:

Author Topic: 2019 what did ya do today.... (Read 196662 times)

Users currently browsing this topic: