Author Topic: 2019 what did ya do today.... (Read 196146 times)

Forwardhandle · « **Reply #2220 on:** December 11, 2019, 08:39:54 AM »

Nice combo Bue

Flem · « **Reply #2221 on:** December 11, 2019, 03:45:28 PM »

Yeah I agree, nice looking wood combo

Is that a typical amount of taper for the design?

Mad Max · « **Reply #2222 on:** December 11, 2019, 04:05:16 PM »

Buemaker · « **Reply #2223 on:** December 11, 2019, 04:08:05 PM »

Usually I do not use a powerlam in a straight limb design, but this time I did. With that amount of taper I think I will not have to make so much adjusting, I’ll let you know how it works out.

Roy from Pa · « **Reply #2224 on:** December 11, 2019, 04:11:02 PM »

Looks nice, Bue.

Bob D · « **Reply #2225 on:** December 11, 2019, 09:22:44 PM »

Today I got short break from the misery of winter. I got to shoot a few arrows and retrieve them while waking on bare ground. Had two days of rain & 45 degrees that melted the snow we had.
Usually we have about 18 inches on the ground by now and you have to shovel before you shoot. Snowing hard out now so that ends that.

Sorry, mini rant. Now back to bow making.

monterey · « **Reply #2226 on:** December 11, 2019, 10:11:21 PM »

Quote from: Buemaker on December 11, 2019, 08:18:13 AM

Putting a trilam together. Belly european hornbeam, center european walnut, backing hard american maple, powerlam jatoba.
Will be a straight limb one with one inch backset.
All three full length lams have a .003 taper.

Looking forward to following this.

ztontonz · « **Reply #2227 on:** December 11, 2019, 10:56:22 PM »

I started shaping the handle and glued the back overlay.
I shot a couple arrow too. Noisy... No hand, good speed but it is loud. I need to think about a way to improve this

Buemaker · « **Reply #2228 on:** December 12, 2019, 10:15:26 AM »

Splicing Osage billets that came all the way from PA. About time is it not Roy?

Roy from Pa · « **Reply #2229 on:** December 12, 2019, 10:47:09 AM »

Heck Bue, they prolly got dry rot by now:)

Mad Max · « **Reply #2230 on:** December 12, 2019, 10:49:20 AM »

Bue has hard wood floors and a desk chair in his shop

Buemaker · « **Reply #2231 on:** December 12, 2019, 10:57:43 AM »

No dry rot, they have been taken well care of.
Need a desk chair in my shop, so I can sit down comfortably and have a stiff drink before operating machines. Need to steady them old nerves.

Flem · « **Reply #2232 on:** December 12, 2019, 11:11:59 AM »

Quote from: Buemaker on December 12, 2019, 10:57:43 AM

No dry rot, they have been taken well care of.
Need a desk chair in my shop, so I can sit down comfortably and have a stiff drink before operating machines. Need to steady them old nerves.

I'm with you on that one Bue. Thats why this is my solvent of choice. Sometimes you need a slap on the head.

Mad Max · « **Reply #2233 on:** December 12, 2019, 04:15:34 PM »

Forwardhandle · « **Reply #2234 on:** December 12, 2019, 05:09:54 PM »

Thats a real man's solvent

Mad Max · « **Reply #2235 on:** December 12, 2019, 06:06:06 PM »

Quote from: Forwardhandle on December 12, 2019, 05:09:54 PM

Thats a real man's solvent

I'll be rite over

Buemaker · « **Reply #2236 on:** December 12, 2019, 06:24:22 PM »

A shot of that 190 proof in the morning should get you going.

scrub-buster · « **Reply #2237 on:** December 13, 2019, 12:45:52 AM »

Today I started on a couple of bow racks out of an old snakey osage log. I got it sliced in half.

I also cut into a wild cherry tree that has been down for a while. It looks like it's spalted in areas. The outside is kind of mushy but the inside seems solid. I think it's worth taking to a saw mill and getting it cut into boards. I'm hoping the spalting gets better towards the trunk.

Flem · « **Reply #2238 on:** December 13, 2019, 10:33:25 AM »

Thats some beautiful, craggy old Osage! Should make some really nice looking rustic racks

Buemaker · « **Reply #2239 on:** December 13, 2019, 11:11:34 AM »

That is some serious looking Osage.

News:

Author Topic: 2019 what did ya do today.... (Read 196146 times)

Users currently browsing this topic: