« previous next »
Pages: [1]   Go Down

Author Topic: Would this concern you?  (Read 2308 times)

Offline mtblucas

  • Trad Bowhunter
  • **
  • Posts: 38
Would this concern you?
« on: July 10, 2019, 02:56:22 PM »
I ended up with a slight gap in my glue line on the belly side of one of my fadeouts. I’m thinking it’ll be fine but was curious what you guys thought. It’s located almost at the thickest part of the fadeout so there shouldn’t be any bending there. The rest of the glue lines on the bow are perfect. Would you be concerned about it if it were your bow? Thanks in advance for any replies.


Logged

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Would this concern you?
« Reply #1 on: July 10, 2019, 03:18:04 PM »
Fill it with glue.
Logged

Shredd

  • Guest
Re: Would this concern you?
« Reply #2 on: July 10, 2019, 03:38:47 PM »
  Your Fine...  As long as it is not hollow all the way through...   Tap on it with the blunt end of a 1/4" drill bit and see if it sounds hollow...  2X what Roy-a-Rooni said...  You might want to heat it up with a heat gun just before you put the glue on... Not too hot to the touch...  The heat will help the glue to flow better and when the area begins to cool it will suck more glue into the joint...  If you don't have a heat gun sit it out in the sun...
Logged

Offline Mad Max

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6565
Re: Would this concern you?
« Reply #3 on: July 10, 2019, 04:35:24 PM »
Yeah
what they said
Logged
I would rather fail at something above my means, than to succeed at something  beneath my means  
}}}}===============>>

Online Crooked Stic

  • TG HALL OF FAME
  • Trad Bowhunter
  • *****
  • Posts: 6075
Re: Would this concern you?
« Reply #4 on: July 10, 2019, 06:06:05 PM »
If it is just a wide glue line you are good.
Logged
High on Archery.

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Would this concern you?
« Reply #5 on: July 10, 2019, 06:26:30 PM »
Quote
I ended up with a slight gap in my glue line on the belly side of one of my fadeouts.

Read it again Spanky...
Logged

Offline Bvas

  • Trad Bowhunter
  • **
  • Posts: 2458
Re: Would this concern you?
« Reply #6 on: July 10, 2019, 07:09:03 PM »
Wouldn’t concern me at all. Have almost the identical thing going on with my current build. I gave it as much super glue as it would take. I’ve put a couple hundred arrows thru it while tillering/timing the limbs. No problem. I am going to put overlays on it. Just because it’s clear glass and looks like crap.
Logged
Some hunt to survive; some survive to hunt

Offline Flem

  • Trad Bowhunter
  • **
  • Posts: 2985
  • "Don't quote me on that!"
Re: Would this concern you?
« Reply #7 on: July 10, 2019, 08:27:47 PM »
I just started using CA glue for a grain filler, as it was recommended by many folks here.
Noticed that it works real good as a gap filler if you dribble some on and sand it in right away.
Might have to be careful with light wood next to dark like you have, probably don't want any light wood dust in the gap.
Logged

Offline mtblucas

  • Trad Bowhunter
  • **
  • Posts: 38
Re: Would this concern you?
« Reply #8 on: July 11, 2019, 03:50:48 AM »
Thanks y’all. After reading your replies I realized it’s not apparent in the pics and perhaps my wording was a bit vague. That “gap” is actually filled solid with epoxy. I guess it’s less of a “gap” and more of a “widening of the glue line.” I was just slightly concerned about the strength of a less than perfect glue line.
Logged

Shredd

  • Guest
Re: Would this concern you?
« Reply #9 on: July 11, 2019, 01:09:19 PM »
  Geez...  For Goodness Sake...  :o   You had us all freaked out and worried about that...  I gotta go...  I think my heart is palpitating...     :laughing:
Logged

Offline Flem

  • Trad Bowhunter
  • **
  • Posts: 2985
  • "Don't quote me on that!"
Re: Would this concern you?
« Reply #10 on: July 11, 2019, 01:20:05 PM »
Yeah, I though we were going to need to have a Bowyers intervention :bigsmyl:
« Last Edit: July 11, 2019, 01:44:32 PM by Flem »
Logged

Offline mtblucas

  • Trad Bowhunter
  • **
  • Posts: 38
Re: Would this concern you?
« Reply #11 on: July 11, 2019, 05:54:54 PM »
Perhaps this is why friends tell me I can be a bit neurotic at times. I used to think they were just joking, haha. I’m not crazy though, this technically is a weak section in the bond, right? If this were in the limb I’d actually be worried about it coming apart at this spot.

Anyway, thanks for making me feel better about this. It was causing lots of anxiety, lol! I guess I don’t have to scrap it and start over now!
Logged

Offline Crittergetter

  • SPONSOR
  • Trad Bowhunter
  • *****
  • Posts: 2634
Re: Would this concern you?
« Reply #12 on: July 11, 2019, 06:13:47 PM »
Concern me , No!
Bug the ever luvin crap outta me, YES!!  :biglaugh:  :biglaugh:


It happens, no biggie!
Logged
An elitist mentality creates discord, even among the elite!
"I went jackalope hunting but all I saw was does!"
Luck is when preparedness meets opportunity, I just need more opportunities!

Offline Wolftrail

  • Trad Bowhunter
  • **
  • Posts: 1152
Re: Would this concern you?
« Reply #13 on: July 11, 2019, 06:27:59 PM »
Not overly concerned but I would still fill it with some CA glue.   You guys have to scale down your pics its like 3MB.   I have a new Dell Computer windows 10 and it loads like a snail having those pics.
Logged

Shredd

  • Guest
Re: Would this concern you?
« Reply #14 on: July 11, 2019, 08:30:39 PM »
Quote from: mtblucas on July 11, 2019, 05:54:54 PM
I’m not crazy though, this technically is a weak section in the bond, right? If this were in the limb I’d actually be worried about it coming apart at this spot.

   Not necessarily...  If the joint does not any major voids or air bubbles it could be just as strong...  Epoxy is different from wood glue... Epoxy works well with a loose fitting joint where as wood glue prefers a tight joint...  Although too loose of a joint is not good either...
Logged

Offline mtblucas

  • Trad Bowhunter
  • **
  • Posts: 38
Re: Would this concern you?
« Reply #15 on: July 12, 2019, 02:59:05 PM »
Quote from: Shredd on July 11, 2019, 08:30:39 PM
Not necessarily...  If the joint does not any major voids or air bubbles it could be just as strong...  Epoxy is different from wood glue... Epoxy works well with a loose fitting joint where as wood glue prefers a tight joint...  Although too loose of a joint is not good either...

Very interesting, I didn’t realize this, but am glad I do now. I am very familiar with using wood glue which is why this this was bugging me.
Logged

Offline mtblucas

  • Trad Bowhunter
  • **
  • Posts: 38
Re: Would this concern you?
« Reply #16 on: July 12, 2019, 03:02:52 PM »
Quote from: Crittergetter on July 11, 2019, 06:13:47 PM
Bug the ever luvin crap outta me, YES!!  :biglaugh:  :biglaugh:

Yup, it definitely does! Oh well, it’s a learning experience I guess. I need to lash it down a little better on the next build. This is my third bow on this form and I haven’t had any issues with it before, so I must’ve gotten a bit complacent.
Logged

Offline Crittergetter

  • SPONSOR
  • Trad Bowhunter
  • *****
  • Posts: 2634
Re: Would this concern you?
« Reply #17 on: July 12, 2019, 03:39:09 PM »
It’s nothing major, We’ve all been there at one point or another!!  Just gotta Keep building and keep learning!!
Logged
An elitist mentality creates discord, even among the elite!
"I went jackalope hunting but all I saw was does!"
Luck is when preparedness meets opportunity, I just need more opportunities!

Shredd

  • Guest
Re: Would this concern you?
« Reply #18 on: July 12, 2019, 05:58:34 PM »
  If everything was done right and sitting flat like it should...    Here are some things that might have happened and things you could do to get better results...

   -  There might have been too big of a gap at that spot for your air hose...  Put a wedge behind your air hose to give you a little more pressure there...

   -  That can be a problematic area because it is too close to the end of the lam...  Instead of continuing your curve to the very end make the last 3/4" to 1" flat...  It will solve the problem...

   -  Watch how thick of a lam you put on there...  If it is a tighter radius you want to stay under .125"...
Logged
Pages: [1]   Go Up
« previous next »

Users currently browsing this topic:

0 Members and 2 Guests are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©