Author Topic: 2020---->What did ya do today? (Read 91316 times)

Shredd · « **Reply #400 on:** March 23, 2020, 05:40:26 PM »

Good Job Mike...

Forwardhandle · « **Reply #401 on:** March 24, 2020, 11:51:21 AM »

I reworked a osage profile form today for beter reflex in the mid to outer limbs gave me 4 1/2" of starting reflex plus I will get another 1 1/2 " for the hooks 6" total starting on 56" osage bow !

Flem · « **Reply #402 on:** March 24, 2020, 11:59:49 AM »

Is that your Laubin style Bow?

Forwardhandle · « **Reply #403 on:** March 24, 2020, 12:13:07 PM »

Yep but I Wasn't happy with the old reflex profile I think Im going to tiller the bow out to 20" before sinew these short bows are tuff for me Im not used to them ! Got a dog (coyote)at dusk yesterday Flem with the new toy !

buddyb · « **Reply #404 on:** March 24, 2020, 02:43:33 PM »

Tried out a new epoxy today, its System Three's G2. I glued up several thin pieces of walnut similar to spectraply for the first time. So far I really like it we'll see how it holds. It reminds me of the epoxies I used back in the 1980s for building bows.

Flem · « **Reply #405 on:** March 24, 2020, 03:22:53 PM »

I don't think you will be disappointed with the G-2. This is what I was using back in the day before System Three bought Industrial Formulators and discontinued it....

I forgot that I had these little samples to try before I had started using the stuff. These have to be 30yrs old and guess what's, it's still good! The resin had crystalized a little, but after a short time in a warm water bath it was good to go. Wish I had more of it.

Crooked Stic · « **Reply #406 on:** March 24, 2020, 04:32:48 PM »

Re doing a old Kodiak Hunter. Found a new use for the threaded insert. For spraying.

buddyb · « **Reply #407 on:** March 24, 2020, 04:47:52 PM »

Flem I think I'll like it as well, its a little more expensive though.

Mike I'd need a ladder to spray the top of that bow.

Eric Krewson · « **Reply #408 on:** March 24, 2020, 04:58:51 PM »

I have been making some special bow making tools for the upcoming St Jude auction. A guy gave me some exhibition grade walnut gunstock cut-offs. This stuff is unreal but I only had enough wood to make 4 gizmos, I even signed these because they are so special.

Flem · « **Reply #409 on:** March 24, 2020, 07:47:09 PM »

Beautiful Walnut! You need some fancy pencils for those

Crooked Stic · « **Reply #410 on:** March 24, 2020, 10:09:29 PM »

Buddy you can take it out of the vise and hold where you need it to be.And the long handle gives some leverage to hold it about any angle. Reclamp until next coat or can hang it to.

buddyb · « **Reply #411 on:** March 24, 2020, 10:51:33 PM »

Great idea Mike, that would work great for my takedown risers.

Crooked Stic · « **Reply #412 on:** March 25, 2020, 07:53:35 AM »

For TD risers I use two long 5/16s bolts to hold and hang them while spraying.

Minnesota Bill · « **Reply #413 on:** March 28, 2020, 04:37:26 PM »

With a little bit of extra time on my hands I decided to get the extra insulation down in the ceiling of my shop. I have had the materials here since November but when I had time the weather was bad. Well the shop is only 16x 9, an old garage that I could not put the car in and open the door. So I took the over head door out several years ago and framed it in to accommodate a 40" swing out door I made. Put 4 inches of insulation in the rafters and covered with OSB so I could still have storage up there. Insulated the walls and boarded it with OSB. Small in wall gas furnace keeps it warm but not enough insulation in attic, snow melts and freezes on roof causing ice dams.
Well so everything stored in the attic was taken out to the driveway, 2x6s nailed in, 6 more inches of insulation placed down and 7/16 OSB placed over the top. Can't hardly crawl though to nail it down, getting awful small up there. That was 2 days ago, I'm starting to be able to move without hurting to much today. Getting old ain't for sissies!!!!!

Buemaker · « **Reply #414 on:** March 28, 2020, 05:30:23 PM »

Insulating in cramped places, yes I know all about that.

Crooked Stic · « **Reply #415 on:** April 01, 2020, 08:27:46 AM »

Mystery block. Green maple and some black sycamore--------------got a plan--

flyonline · « **Reply #416 on:** April 02, 2020, 09:09:08 PM »

Got sent home yesterday, my wife was displaying 'some' of the C19 symptoms and works with vulnerable people so went to get tested. I've been canned from work until the results come back, so might as well make the best of it

Worked on my latest Osage selfbow, 69" and hoping for 50+ @ 28" so I'm legal for deer. So far it's 45 @23 with a couple of whoopsies to work out so hopefully should come in on target. I had to do a little straightening and de-propping with dry heat which leaves it with a little deflex in one limb, and reflex in the other. The left limb is bottom with a slight reflex in the last 1/4 of the limb, and the right has a slight deflex about halfway out.

Flem · « **Reply #417 on:** April 03, 2020, 08:32:02 AM »

Steve, it looks like most all of your bend is in the handle area?

Pat B · « **Reply #418 on:** April 03, 2020, 09:57:35 AM »

Leave the center 1/3 alone and get both mid limbs working. That will relieve the over binding in the handle area a bit...and don't bend it that far again until you correct the problem.
Are you exercising the limbs after each wood removal?

kennym · « **Reply #419 on:** April 03, 2020, 08:07:23 PM »

Quote from: Crooked Stic on April 01, 2020, 08:27:46 AM

Mystery block. Green maple and some black sycamore--------------got a plan--

That looks cool Mike!!

I worked in shop and listened to it rain...

Started a bow blank for a feller with lams from scrap barrel and a riser block that was messed up on an end...

News:

Author Topic: 2020---->What did ya do today? (Read 91316 times)

Shredd

Users currently browsing this topic: