Author Topic: 2020---->What did ya do today? (Read 91282 times)

beachbowhunter · « **Reply #460 on:** April 24, 2020, 10:45:33 AM »

Gives me the willies everytime you post these!

kennym · « **Reply #461 on:** April 24, 2020, 11:54:00 AM »

Norb- cost is no object to a bow addict!

Crooked Stic · « **Reply #462 on:** April 24, 2020, 08:00:12 PM »

Here ya go.

BO-R · « **Reply #463 on:** April 25, 2020, 08:48:49 AM »

Nice work, stic..
have to give that a go at some point.

kennym · « **Reply #464 on:** April 25, 2020, 08:51:06 AM »

What?? No big hammer?

Nice job!!

Shredd · « **Reply #465 on:** April 25, 2020, 09:14:57 AM »

Nice... Yer gitten purty good at making 'em, Mike....

Crooked Stic · « **Reply #466 on:** April 25, 2020, 02:40:30 PM »

I think the thing is keep the tenon parallel front to back and about.008 taper on sides. almost falls out on its own but no wiggle when together so far.

Buemaker · « **Reply #467 on:** April 25, 2020, 03:32:22 PM »

Looks like a perfect fit, nice.

kennym · « **Reply #468 on:** April 25, 2020, 06:27:17 PM »

That makes good sense , Mike!

Shredd · « **Reply #469 on:** April 26, 2020, 12:45:42 AM »

That Parallel may get you in trouble down the line...

Crooked Stic · « **Reply #470 on:** April 26, 2020, 07:09:04 AM »

Quote from: Shredd on April 26, 2020, 12:45:42 AM

That Parallel may get you in trouble down the line...

Explain??

Shredd · « **Reply #471 on:** April 26, 2020, 06:16:26 PM »

Might get stuck with a one pc. bow... I think there is a general rule in mold making... Make a mold with a 1 to 2* taper so that you can remove the pc. from the mold...

Crooked Stic · « **Reply #472 on:** April 26, 2020, 08:36:54 PM »

Well sir done my last three like that no more than .003 taper. this one had .002 Jim sez try to keep them parallel frt. to bck. Taper on the sides.
Anyhow this one has KY.coffeebean veneers quarter sawen.

flyonline · « **Reply #473 on:** April 27, 2020, 06:08:27 AM »

Quote from: Pat B on April 03, 2020, 09:57:35 AM

Are you exercising the limbs after each wood removal?

Yep, 20-40 pulls each time. Long story short there was a bit of operator mis-read which was compounded by an equipment challenge and I ended up with a couple of very mismatched limbs so I've thrown it in the corner but might pull it out at some stage and rescue it for something - can probably make a very light/kids bow if I weaken up the strong limb to match. Haven't had a good run, another equipment malfunction (read operator error) meant I ended with an overly short r/d boo backed cypress board bow which looked great until I went too far with a long string and took too much off the tips <sigh> Again, I can probably take it back to a lightish/kids bow so I threw it in the other corner until I forgive it enough to get back to it.

Soo, I started on my latest - a 66" ASL from spotted gum with boo backing (if I screw this up I've still got a 4th corner before I get back to the beginning

). It's 1.25" straight until the last 8" tapering to 1/2" with a 12" riser and I'm planning on a straight glue up to keep it simple. This is the first fully shaped riser/handle that I've done, and I'm a little unsure how to shape out the fades to paper thin with my limited tools. Belt sander mounted on it's side and use the end roller as a kinda spindle sander?

Flem · « **Reply #474 on:** April 27, 2020, 09:15:41 AM »

Interesting....... I have wondered about using Eucalyptus. It's pretty wood, really heavy!
Is it at all brittle? For your fades, if you can get a clean cut close to the line, you can taper it without too much trouble with varying grits of sandpaper wrapped around some 2-3" PVC pipe

ztontonz · « **Reply #475 on:** April 27, 2020, 06:59:24 PM »

Quote from: Crooked Stic on April 26, 2020, 08:36:54 PM

Well sir done my last three like that no more than .003 taper. this one had .002 Jim sez try to keep them parallel frt. to bck. Taper on the sides.
Anyhow this one has KY.coffeebean veneers quarter sawen.

I like the look of your veneers!

flyonline · « **Reply #476 on:** April 28, 2020, 05:28:12 AM »

Quote from: Flem on April 27, 2020, 09:15:41 AM

Interesting....... I have wondered about using Eucalyptus. It's pretty wood, really heavy!
Is it at all brittle? For your fades, if you can get a clean cut close to the line, you can taper it without too much trouble with varying grits of sandpaper wrapped around some 2-3" PVC pipe

Flem

I can't really comment not having worked much/made a bow with it yet but I do know spotted gum has been used successfully here quite a bit both in board and stave form. I suspect it's a bit like your hickory and red oak, not the first choice but readily available and works ok. It would be interesting to see if some heat treating does anything for it. There are other eucalyptus' that have been used successfully also, but they're much harder to get hold of in general. It's unfortunate that our other widely available eucatlyp in mountain ash/tassie oak etc. makes poor bows as it's relatively easy to find in straight grained boards.

Roger on the PVC, I'm assuming you're talking about final shaping once glued up on the bow?

Crooked Stic · « **Reply #477 on:** April 28, 2020, 08:00:41 PM »

Scrappy. A buddy needs a riser for one set of his Black Hunter limbs. Some left over camo and bloodwood. And am seeing why they sell these bows so cheap.

Flem · « **Reply #478 on:** April 28, 2020, 10:38:11 PM »

Steve, since you mentioned wanting to get your fades paper thin, this is what I was thinking.

flyonline · « **Reply #479 on:** April 29, 2020, 11:25:19 PM »

Thanks Flem, ended up doing a combo of all three - cut closeish, belt sander, finish with pipe. Worked fine with a bit of elbow grease and got them see through on the tips

Only question is, will the nodes at the end of the fades create a problem when tillering?

News:

Author Topic: 2020---->What did ya do today? (Read 91282 times)

Shredd

Shredd

Shredd

Users currently browsing this topic: