Author Topic: Paracord String Silencers (Read 8251 times)

LongbowArchitect · « **Reply #20 on:** June 23, 2020, 12:59:01 PM »

Hey Wudstix. Did you tie in the pieces of paracord or just insert them between the string strands? Thanks for the tip. I'm going to give them a try.

Wudstix · « **Reply #21 on:** June 23, 2020, 02:41:07 PM »

Simply inserted paracord sheaths with white inner threads removed in string and then squeezed them together a bit.

Paul Fithian · « **Reply #22 on:** June 24, 2020, 01:48:56 PM »

Here's a super easy way to set these up:
1) Wrap the paracord around 4 fingers on one of your hands to get 6 pieces. Cut and pull out the inner strands. Save 2 of the strands.
2) Cut the sheath length in half.
3) Cut each of those into 3 pieces
4) Use one of the inner strands to tie the 3 sheath pieces to the string with double overhand knots on top and bottom. Rotate the sheath pieces so that they are even around the string.
5) Shoot the bow to fray the sheath into a silencer

Holm-Made · « **Reply #23 on:** June 24, 2020, 02:42:34 PM »

Would it look/work better if you used three different length pieces rather then all the same length?

Wudstix · « **Reply #24 on:** June 24, 2020, 05:28:54 PM »

Don’t see why not just be non-symetrical.

Wudstix · « **Reply #25 on:** June 30, 2020, 09:44:42 PM »

Finally felt like shooting after work this evening. Put another 61 arrows down range at 10-12-15 yards with about 4” six arrow groups with 2315 plus a heavy woodie. Paracord adjusted to 12” from nock groove, quieter. Think I found the sweet spot. They’re fluffing out nicely. Still a small “click” in the shot may try shorter/stiffer shafts tomorrow night. Or try some 2219, or heavy hardwood, Hmmm!!!

Wudstix · « **Reply #26 on:** July 01, 2020, 10:00:35 PM »

Top and bottom after 201 shots. Looking pretty good.

Wudstix · « **Reply #27 on:** July 01, 2020, 10:09:50 PM »

Five arrow group at 13 yards. Two sticking out the back.

Deertaker · « **Reply #28 on:** July 02, 2020, 11:16:57 AM »

So I have used 2 pieces of chord to silence my bow and it works great. The only issue is that when you slide them into the string they sometimes move. I like sliding them in the string, but does anyone have some pictures or suggestions for knots to tie to prevent them from moving? I have tried the constrictor knot, but hoping there might be a better knot to try? Any pics would be greatly appreciated!

Wudstix · « **Reply #29 on:** July 02, 2020, 01:38:32 PM »

Do you use just the sheaths between the string? I have four sheaths and was able to adjust a bit with unstrung bow before they got real fluffy. But they haven’t slid at all.

Deertaker · « **Reply #30 on:** July 03, 2020, 08:11:29 AM »

yes, I just slide them between. and seems like every time they slide, I keep pulling them back and they keep sliding.

Wudstix · « **Reply #31 on:** July 03, 2020, 07:35:13 PM »

I’ve seen three recommended, I use four and squeezed them together with no slippage after they frizzed and fluffed out.

gnome · « **Reply #32 on:** July 04, 2020, 08:39:29 AM »

Quote from: Wudstix on July 02, 2020, 01:38:32 PM

Do you use just the sheaths between the string? I have four sheaths and was able to adjust a bit with unstrung bow before they got real fluffy. But they haven’t slid at all.

Quote from: Deertaker on July 02, 2020, 11:16:57 AM

So I have used 2 pieces of chord to silence my bow and it works great. The only issue is that when you slide them into the string they sometimes move. I like sliding them in the string, but does anyone have some pictures or suggestions for knots to tie to prevent them from moving? I have tried the constrictor knot, but hoping there might be a better knot to try? Any pics would be greatly appreciated!

I'm with wudstix..... there are no knots involved.... just insert between the string bundles...

deertalker.... when you say slide , do you mean up and down the string?...... then try a tied nock point above and below to keep them from migrating... If they are slipping out from between the string bundles ..... cut the para cord about 6"+, insert between the bundles, and tie an overhand knot, cinched tight, trim to length.... lather, rinse, repeat.

gnome · « **Reply #33 on:** July 04, 2020, 08:51:23 AM »

not very good photos, but it shows an extra loop around the string with the cord so it doesn't pull out.

Wudstix · « **Reply #34 on:** July 06, 2020, 02:43:23 PM »

I have been a Qiviut fan and alpaca wool for years due to light weight and water shedding, paracord is noticeable faster than wool puffs and cost savings is substantial. The water shed test will come and that could be it.

Wudstix · « **Reply #35 on:** July 09, 2020, 09:10:45 PM »

Moved the PC string silencers two inches to 1/4 of string length from nocks and Eureka, noise gone and arrow flight is amazing with very tight four arrow groups.

Bruce M · « **Reply #36 on:** July 10, 2020, 02:36:01 PM »

Quote from: Wudstix on July 09, 2020, 09:10:45 PM

Moved the PC string silencers two inches to 1/4 of string length from nocks and Eureka, noise gone and arrow flight is amazing with very tight four arrow groups.

What do you mean by “two inches to 1/4 of string length “.
Do you mean you divided the string length in quarters and positioned the silencers at 1/4 of the length from each end

Wudstix · « **Reply #37 on:** July 10, 2020, 06:05:25 PM »

Yes, string 56” NTN so moved from 12” to 14” and that is the spot.

Bruce M · « **Reply #38 on:** July 10, 2020, 08:12:17 PM »

okay thanks.

Wudstix · « **Reply #39 on:** July 10, 2020, 08:30:02 PM »

That works for my 63-67# hybrid longbows, best. Also, for Big River recurve 66#.


LEFT HAND BOWS CLASSIFIEDS	TRAD GANG CLASSIFIEDS ACCESS	RIGHT HAND BOWS CLASSIFIEDS

News:

Author Topic: Paracord String Silencers (Read 8251 times)

Users currently browsing this topic: