Author Topic: Something New (Read 15153 times)

Mad Max · « **Reply #40 on:** January 08, 2021, 10:00:07 AM »

Lookin forward

I like a .002 with 1-1/2"wide at the riser and just a little wider than .001 taper 5" from the Nock

Flem · « **Reply #41 on:** January 08, 2021, 11:27:36 AM »

Stic, can we talk you into doing a how to on wood stabilizing sometime?

Longcruise · « **Reply #42 on:** January 08, 2021, 02:10:07 PM »

Quote from: Crooked Stic on January 07, 2021, 07:44:33 PM

The form is finished. Got on the strap spacers and lam keepers. I will use a zip tie to pull the lams down on the curve.
Mr Roy my old walnut is kinda slow about taking in the juice

I like those keepers. Did you make them from scratch or start with a likely suspect?

Crooked Stic · « **Reply #43 on:** January 08, 2021, 08:19:33 PM »

I have used washers but was not happy with how they worked out. I think I seen something like these only wood and one bolt. So I come up with the slot and two bolts.
I got some lams ground out today and accents in the riser block but no pics.

My walnut still soaking juice

Crooked Stic · « **Reply #44 on:** January 09, 2021, 06:58:33 PM »

One limb cooking now.
Riser block cleaned up and squared. Black Frogwood MD with osage and maple accents.

Mad Max · « **Reply #45 on:** January 09, 2021, 07:08:50 PM »

Osage always looks good with dark wood

BO-R · « **Reply #46 on:** January 10, 2021, 08:46:07 AM »

coming along nice!

BO-R · « **Reply #47 on:** January 10, 2021, 08:47:21 AM »

how do you like the frog wood compared to dymondwood?

Crooked Stic · « **Reply #48 on:** January 10, 2021, 11:07:59 AM »

This is the medium density stuff more like the old actionwood. Mat be better than Spectraply because the layers are thinner and makes it more dense . They do have a High density that I have not tried yet. But would think it will be comparable to dymondwood. And you dont have to buy a full panel.
So I went out to unplug the hotbox. So I went ahead and got the limb out ( All I am doing today ) seems I got plenty of glue on it

Roy from Pa · « **Reply #49 on:** January 10, 2021, 01:20:09 PM »

Nice, Mike.

Crooked Stic · « **Reply #50 on:** January 11, 2021, 05:51:47 PM »

Thanks Roy.

Second limb cookin and riser sled made today.

Mad Max · « **Reply #51 on:** January 11, 2021, 06:20:36 PM »

Moving right along stic, lookin good

Roy from Pa · « **Reply #52 on:** January 11, 2021, 07:07:52 PM »

Oh I like that a lot.

Crooked Stic · « **Reply #53 on:** January 12, 2021, 05:17:00 PM »

Well I had therapy at 1:20 so got some done this morning. Cleaned the limbs up to width.
Put a hold down on the riser sled being it only has a very small stop on the corner. And sliced the ends of.
As you can see I need to slim the wedge ramps down some on the next one.

Roy from Pa · « **Reply #54 on:** January 12, 2021, 05:39:57 PM »

Longcruise · « **Reply #55 on:** January 12, 2021, 07:30:23 PM »

I'm kinda excited about this!

Crooked Stic · « **Reply #56 on:** January 12, 2021, 09:38:15 PM »

Yeah I just hope it don't come out too heavy. I got this body builder buddy that can prolly handle it if it does.

Flem I just seen your request on the stabilizing. I do have a piece soaking now. Will start a thread on it soon.

Flem · « **Reply #57 on:** January 12, 2021, 11:25:50 PM »

Your a good man stic!

Crooked Stic · « **Reply #58 on:** January 13, 2021, 05:13:21 PM »

Okay got some time in on this one today. I got everything drilled and the limbs on. Seemed to look good with the string down the center.
The rest of this one may really be delayed. Got word today that my mom may be going to Hospice. With all the restrictions on Covid it is really hard to even get in to see her.

Crooked Stic · « **Reply #59 on:** January 14, 2021, 05:23:56 PM »

I got very little done today. Got the tips tapered and some tip overlay pieces ready fo glue
My mom has gotten a lot worse and going to hospice tomorrow so we went up to see her today.

News:

Author Topic: Something New (Read 15153 times)

Users currently browsing this topic: