Author Topic: Boo slat bow (Finished) (Read 1791 times)

Mad Max · « **on:** January 15, 2021, 01:07:19 PM »

If I was to do this again I would start with the thickest Boo slat I could find.
I was sure it was going to take set but still a fun project. 60" NTN 30#@28"

String serving

Leather dye

Belly

Roy from Pa · « **Reply #1 on:** January 15, 2021, 01:10:25 PM »

Very nice, Mark.

Longcruise · « **Reply #2 on:** January 15, 2021, 01:23:36 PM »

Nice!

Flem · « **Reply #3 on:** January 15, 2021, 01:51:22 PM »

Damn your good

Kind of looks like a Holmegaard in that front view.
Very nice

Longcruise · « **Reply #4 on:** January 15, 2021, 02:01:51 PM »

Quote from: Flem on January 15, 2021, 01:51:22 PM

Damn your good
Kind of looks like a Holmegaard in that front view.
Very nice

Yes, ive toyed with the idea of a glass bow in that design. Might still do it. I built one very similar with a red oak board and a tapered overlay to stiffen the tips. It came in very light but was still a decent shooter and is still floating around in the family somewhere.

Biggest design differences were no reflex and the working portion of the limb was a pyramid design.

Roy from Pa · « **Reply #5 on:** January 15, 2021, 02:48:32 PM »

What is the principle behind that limb design?

mmattockx · « **Reply #6 on:** January 15, 2021, 03:02:52 PM »

Very nice.

Mark

Mad Max · « **Reply #7 on:** January 15, 2021, 03:25:40 PM »

Quote from: Roy from Pa on January 15, 2021, 02:48:32 PM

What is the principle behind that limb design?

I can't find the info. I want.
Go down the page to the pictures of the side profile roy
http://www.atarn.org/letters/ltr_jul02.htm

Thanks guy's

Roy from Pa · « **Reply #8 on:** January 15, 2021, 03:27:35 PM »

Crooked Stic · « **Reply #9 on:** January 15, 2021, 04:46:02 PM »

That thing is kinda sexy lookin

kennym · « **Reply #10 on:** January 15, 2021, 04:55:37 PM »

Cool bow Mark!!

Mad Max · « **Reply #11 on:** January 15, 2021, 05:10:18 PM »

Quote from: Crooked Stic on January 15, 2021, 04:46:02 PM

That thing is kinda sexy lookin

you've been out in the bow shop to long

It does don't it

kennym · « **Reply #12 on:** January 15, 2021, 05:36:37 PM »

Probly the sheep horn tips...

Pat B · « **Reply #13 on:** January 15, 2021, 08:25:19 PM »

I love the unbraced, braced and full draw profile. The width of the working part of the limbs looks too blocky for my liking but what do I know. From the look of the bend the outer portion doesn't seem to be doing much work. The last 6" of the working limb could be tapered to reduce physical weight which could add to the performance.
Very nice bow!!!

Roy from Pa · « **Reply #14 on:** January 15, 2021, 08:41:45 PM »

I guess it's ok...

Mad Max · « **Reply #15 on:** January 15, 2021, 09:26:51 PM »

Thanks guy's
roy

Shredd · « **Reply #16 on:** January 16, 2021, 12:15:34 AM »

Beautiful lines... Great job Buddy...

flyonline · « **Reply #17 on:** January 16, 2021, 01:11:40 AM »

Nice! How wide are the limbs, and how thick is the boo in the center? I've contemplated something similar but I can't get boo with enough diameter to get a flat enough slat out of it.

Buemaker · « **Reply #18 on:** January 16, 2021, 03:32:00 AM »

That is a good looking bow.

Mad Max · « **Reply #19 on:** January 16, 2021, 09:46:40 AM »

I started out on the edge sander to get them flat and measured the thickness and got both of them the same thickness, I was impressed when I braced it and it only needed scraping the last 6" of working limb, I also got the 8" of tip bending a little. It tillered itself almost

It's 5/16" thick when I measured it last .
you can see the bare/raw inside on the whole working limb in this picture, about 3/8" flat above and below the CA glue

you can see the bare/raw about 6" long mid limb (in the Picture) left over after it was finished

the boo was full width and all I did was sand the sides a little to parallel the sides, just under 1-3/4"

Thanks guy's

News:

Author Topic: Boo slat bow (Finished) (Read 1791 times)

Shredd

Users currently browsing this topic: