Author Topic: Limb alignment. (Read 1876 times)

Cherry Tree · « **on:** January 17, 2021, 06:28:47 PM »

Does anyone know where a guy can get a set of machined limb alignment brackets and cable for finding the dynamic center of limbs? Or anyone capable of making them? Thanks.

Crooked Stic · « **Reply #1 on:** January 17, 2021, 10:03:16 PM »

Mine are alum. bar stock. 1 1/4 I think. I got mine way back from Horne bows. You could stack some big washers together weld them and make your own.
THe last pic on my something new thread has them on a bow.

4 point · « **Reply #2 on:** January 17, 2021, 10:41:22 PM »

Hey Mike, how thick are yours?

Roy from Pa · « **Reply #3 on:** January 18, 2021, 06:11:42 AM »

Here is mikes string alignment.

Crooked Stic · « **Reply #4 on:** January 18, 2021, 08:37:35 AM »

5/16 or 3/8s maybe.

Roy from Pa · « **Reply #5 on:** January 18, 2021, 08:46:44 AM »

Mike how bout a picher from the tip end?

Cherry Tree · « **Reply #6 on:** January 18, 2021, 09:11:25 AM »

3/8s is what I was thinking. Close up pictures would be great!

Crooked Stic · « **Reply #7 on:** January 18, 2021, 09:21:27 AM »

Here is a set that Big Jim sent me a pic of with a cable.

Roy from Pa · « **Reply #8 on:** January 18, 2021, 09:42:00 AM »

Sweet....

Longcruise · « **Reply #9 on:** January 18, 2021, 10:44:57 AM »

Mike, do you interchange strings on your system? Big Jim's looks like it might be an adjustable cable??

Maybe a turn buckle adaptor??

Getting ready to do the first RC and think one of these would be almost a requirement.

williwaw · « **Reply #10 on:** January 18, 2021, 04:23:33 PM »

Quote from: Crooked Stic on January 17, 2021, 10:03:16 PM

Mine are alum. bar stock. 1 1/4 I think. I got mine way back from Horne bows. You could stack some big washers together weld them and make your own.
THe last pic on my something new thread has them on a bow.

do you take them to full draw?

Crooked Stic · « **Reply #11 on:** January 18, 2021, 08:18:38 PM »

Usally the correct length string will work being as the grooves will be about where the string will be in the blocks. Another note is when you cut your limb off it needs to be square where the block sets. Once you are happy with the placement. make a line on each side of the block then half way between is dynamic center.
But I am betting if your lam grind is dead on with no grain runout Center will be center.
Use no more than.001 forward taper and lighter weight bows 40 or less no taper. Makes things a lot easier.

Buemaker · « **Reply #12 on:** January 19, 2021, 03:33:55 AM »

Like your blocks Mike.

kennym · « **Reply #13 on:** January 19, 2021, 07:48:50 AM »

You could cut aluminum on your bandsaw I think. Might be hard on blades, and I would clamp a piece of plywood on the table for a zero clearance insert ( cut into it and clamp it) because the plastic insert on most saws won't take cutting something that small without sucking it down thru the insert.

Trust me you don't want that!

Been there- costs ya a blade and an insert...

Roy from Pa · « **Reply #14 on:** January 19, 2021, 07:58:20 AM »

Been there- costs ya a blade and an insert.

Yupper, I've seen that happen a time or two:)

kennym · « **Reply #15 on:** January 19, 2021, 08:06:33 AM »

And maybe a pair of undies

jess stuart · « **Reply #16 on:** January 19, 2021, 08:49:06 AM »

I made mine from 1/2" thick phenolic. I used a small cable and adjust the cable length for bows from 48" to 66".

Roy from Pa · « **Reply #17 on:** January 19, 2021, 09:09:51 AM »

Depends, Kenny...

Mike how do you string the bow and have you ever had one of those slip off with the bow strung?

Crooked Stic · « **Reply #18 on:** January 19, 2021, 10:00:42 AM »

Two pegs on the side of the bench bottom limb under a peg riser on top of peg push top limb down to string.
Yes I tried pulling a recurve with them on and it came off that limb was a b to get right after slamming the floor very hard.

Roy from Pa · « **Reply #19 on:** January 19, 2021, 10:05:23 AM »

LOL, ya have a video of that?

News:

Author Topic: Limb alignment. (Read 1876 times)

Users currently browsing this topic: