Author Topic: 2021 Bow Swap Progress Thread - Complete (Read 148231 times)

canopyboy · « **Reply #400 on:** February 16, 2021, 04:41:03 PM »

Quote from: Mad Max on February 16, 2021, 03:23:40 PM

What edge sander do you have there Canopyboy?

It's a canopyspecial...

I didn't like what I could get commercially. I wanted a longer platten without getting a bigger sander, so I cogitated on it for awhile in meetings where I couldn't pay attention anyhow and came up with that thing. Works well enough...

Mad Max · « **Reply #401 on:** February 16, 2021, 04:49:36 PM »

Roy from Pa · « **Reply #402 on:** February 16, 2021, 05:26:27 PM »

Ya did well David..

Buemaker · « **Reply #403 on:** February 16, 2021, 06:02:28 PM »

Thanks Max, I understand now.

Mad Max · « **Reply #404 on:** February 16, 2021, 06:59:31 PM »

Bue

Mo_coon-catcher · « **Reply #405 on:** February 16, 2021, 09:00:18 PM »

I made a bit more progress today. It’s about 2” shy of full draw. A little sanding and shooting in should get it right on. Well counting on it holding up through the shoot in process. It’s taken about 1/4” set with about 1/2” right after unbracing. I’m kinda surprised it’s held up with so little set and no chrysalling this far. And I like the mass.

Kyle

Roy from Pa · « **Reply #406 on:** February 16, 2021, 09:14:44 PM »

Just curious, it looks flat through this section.

Mo_coon-catcher · « **Reply #407 on:** February 16, 2021, 09:24:40 PM »

It is a little flatter there than I intended. I was hoping to leave that stiff until the last three inches of draw. And just sand the center into draw weight. The stave is 60” between the nocks for a 27” draw. I like to leave the center a bit stiff when I make a bendy handle longer than a 2x draw weight ratio. I do appreciate all critiques of the tiller.

Kyle

kennym · « **Reply #408 on:** February 17, 2021, 12:27:51 PM »

Did a little riser work

Mad Max · « **Reply #409 on:** February 17, 2021, 12:42:03 PM »

Who are you making that for, Batman

kennym · « **Reply #410 on:** February 17, 2021, 01:15:56 PM »

Can’t tell ya

Roy from Pa · « **Reply #411 on:** February 17, 2021, 02:51:43 PM »

Sweet riser there ole timer:)

kennym · « **Reply #412 on:** February 17, 2021, 03:13:38 PM »

Thanks Pops

Crooked Stic · « **Reply #413 on:** February 17, 2021, 04:10:17 PM »

Nice Kenny.

Mad Max · « **Reply #414 on:** February 17, 2021, 04:19:43 PM »

Dannon · « **Reply #415 on:** February 17, 2021, 06:04:35 PM »

Looking good Kenny!

skeaterbait · « **Reply #416 on:** February 17, 2021, 07:05:46 PM »

Quote from: Mad Max on February 17, 2021, 12:42:03 PM

Who are you making that for, Batman

Nah, check the colors, it's for the Green Lantern

Mo_coon-catcher · « **Reply #417 on:** February 17, 2021, 08:31:15 PM »

You must become one with your bow🧘‍♂️.And yes I was glued to it, starbond is a wonderful superglue. Deer antler felt like a fitting overlay material on this one. Though I rarely use it.

Kyle

Mad Max · « **Reply #418 on:** February 17, 2021, 08:47:52 PM »

4 point · « **Reply #419 on:** February 17, 2021, 09:49:32 PM »

I like that riser Kenny!

News:

Author Topic: 2021 Bow Swap Progress Thread - Complete (Read 148231 times)

Users currently browsing this topic: