Author Topic: New static----DONE (Read 7694 times)

Mad Max · « **Reply #20 on:** February 18, 2021, 09:19:01 PM »

I think it's 7 ply. plywood
1-1/2" form

Mad Max · « **Reply #21 on:** April 05, 2021, 06:37:55 PM »

I got the riser pattern template to fit the form done today and pattern sanded some Osage.
I will make one for the riser belly to pattern sand most of it.

Riser is 16"

Walt Francis sent me his so I measure it up

I was close in most of it but the fades.
Walt's is 63#@27"

Roy from Pa · « **Reply #22 on:** April 05, 2021, 08:55:03 PM »

kennym · « **Reply #23 on:** April 05, 2021, 09:34:48 PM »

This should be good!!

bigbob2 · « **Reply #24 on:** April 09, 2021, 10:03:48 PM »

I reckon it will have some oomph!

Mad Max · « **Reply #25 on:** April 10, 2021, 08:24:30 AM »

Still a lot of work to do on the form, it has a little warp from end to end so I have some angle iron to bolt to it, and the hardware for the form and the washers to keep the lams in line. I may have to make the form hardware because of the angle iron being in the way.

Mad Max · « **Reply #26 on:** April 22, 2021, 07:05:54 PM »

50# now still needs rounding over

Off the form and buggers cleaned up.

Profiled the limb width

The other bow is behind my bow, mine needs a little tiller adjustment.

I put the 2 pictures together on paint

Shredd · « **Reply #27 on:** April 22, 2021, 07:58:51 PM »

Roy from Pa · « **Reply #28 on:** April 22, 2021, 08:47:57 PM »

Nice job...

Buemaker · « **Reply #29 on:** April 23, 2021, 03:42:35 AM »

Gonna be a lot of sheepeating now.

Mad Max · « **Reply #30 on:** April 23, 2021, 08:19:35 AM »

Birdbow76 · « **Reply #31 on:** April 23, 2021, 10:08:05 AM »

That's a cool little bow. I wanted one of those Sheepeater's when they were being made but never got around to it.

Mad Max · « **Reply #32 on:** April 23, 2021, 02:48:11 PM »

I looked for many years and never could find one.

Roy from Pa · « **Reply #33 on:** April 23, 2021, 03:03:35 PM »

Well ya have a nice one now....

Mad Max · « **Reply #34 on:** April 23, 2021, 05:43:58 PM »

Buemaker · « **Reply #35 on:** April 23, 2021, 05:48:57 PM »

Interesting design. What taper rate are you using and what was used in the Sheepeater?

Mad Max · « **Reply #36 on:** April 23, 2021, 06:43:45 PM »

Same as the Sheepeater, .00something

kennym · « **Reply #37 on:** April 23, 2021, 07:29:34 PM »

Quote from: Mad Max on April 23, 2021, 06:43:45 PM

Same as the Sheepeater, .00something

Can you make that in a fraction so's you don't cornfuse Rody?

Roy from Pa · « **Reply #38 on:** April 23, 2021, 07:31:45 PM »

I fuggered it out...

ztontonz · « **Reply #39 on:** April 23, 2021, 07:53:02 PM »

Coming allong nicely!

News:

Author Topic: New static----DONE (Read 7694 times)

Shredd

Users currently browsing this topic: