INFO: Trad Archery for Bowhunters



« previous next »
Pages: [1] 2   Go Down

Author Topic: Self Nock Woodies Build  (Read 11795 times)

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Self Nock Woodies Build
« on: March 22, 2021, 09:40:38 AM »
Nothing fancy, just some knock-about hunting shafts.  11/32" Surewood fir, 55-60# spine, 28-1/4" length, Tru-Flight turk LW feathers, CA glue to adhere the nock inserts that were slotted with a Nifty Nocker, two thin coats of wipe-on polyU, Bohning tape and CA for fletching, 362 grains average weight with no point.  "Cresting" accomplished with a v/s electric drill, a "V" block, and Sharpie pens.

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Re: Self Nock Woodies Build
« Reply #1 on: March 22, 2021, 09:42:26 AM »
 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Re: Self Nock Woodies Build
« Reply #2 on: March 22, 2021, 09:44:03 AM »
 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Re: Self Nock Woodies Build
« Reply #3 on: March 22, 2021, 09:45:05 AM »
 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]

 [ You are not allowed to view attachments ]
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Self Nock Woodies Build
« Reply #4 on: March 22, 2021, 09:53:27 AM »
 :thumbsup: :thumbsup: :thumbsup: :thumbsup:
Logged

Offline rustyspike

  • Trad Bowhunter
  • **
  • Posts: 206
Re: Self Nock Woodies Build
« Reply #5 on: March 22, 2021, 03:55:11 PM »
They came out very nice.

Rich K.
Logged

Online Deno

  • Trad Bowhunter
  • **
  • Posts: 884
Re: Self Nock Woodies Build
« Reply #6 on: March 22, 2021, 04:20:49 PM »
Great job Rob  :thumbsup: :thumbsup: :thumbsup:

Deno
Logged
United Bowhunters of New Jersey
Traditional Archers of New Jersey
Traditional Archery Society
Howard Hill Wesley Special 70#
Howard Hill Big 5  65#

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Self Nock Woodies Build
« Reply #7 on: March 22, 2021, 05:09:51 PM »
What type of wood is used in that slot you cut out?
Logged

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Re: Self Nock Woodies Build
« Reply #8 on: March 22, 2021, 05:16:10 PM »
Quote from: Roy from Pa on March 22, 2021, 05:09:51 PM
What type of wood is used in that slot you cut out?

Model aircraft birch plywood.  I wick in water thin hobby shop CA (Hot Stuff brand) to really harden the entire nock area, both for the reinforcing ply and the string nock slot itself.
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Offline bigbadjon

  • Trad Bowhunter
  • **
  • Posts: 1472
Re: Self Nock Woodies Build
« Reply #9 on: March 22, 2021, 05:34:10 PM »
I haven't built any in a spell, but that Nifty Nocker jig from Raptor is the cat's ass.
Logged
Hoyt Tiburon 55#@28 64in
A&H ACS CX 61#@28in 68in (rip 8/3/14)

Offline Rob DiStefano

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 12246
  • Contributing Member
    • Cavalier Pickups
Re: Self Nock Woodies Build
« Reply #10 on: March 22, 2021, 05:42:53 PM »
Quote from: bigbadjon on March 22, 2021, 05:34:10 PM
I haven't built any in a spell, but that Nifty Nocker jig from Raptor is the cat's ass.

Absolutely, it's the 2nd gen version and uses an adjusting compression collar to hold in 5/16" to 23/64" shafts, whereas the older version required separate sized shaft ferrules which was harder to keep the shaft aligned during tightening.
Logged
IAM ~ The only government I trust is my .45-70 ... and my 1911.

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Self Nock Woodies Build
« Reply #11 on: March 22, 2021, 05:51:11 PM »
 :thumbsup: :thumbsup:
Logged

Online Terry Green

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 28708
Re: Self Nock Woodies Build
« Reply #12 on: March 22, 2021, 06:11:07 PM »
People have no idea what a wealth of information Rob is.  Take this and the fact that he runs the guts of TG is a miss to so many.... PAY ATTENTION!
Logged
Tradbowhunting Video Store - https://digitalstore.tradgang.com/

Tradgang Bowhunting Merchandise - https://tradgang.creator-spring.com/?

Tradgang DVD - https://www.tradgang.com/tgstore/index.html

"It's important,  when going after a goal, to never lose sight of the integrity of the journey" - Andy Garcia

'An anchor point is not a destination, its  an evolution to conclusion'

Offline J. Adams

  • TGMM Member
  • Trad Bowhunter
  • ***
  • Posts: 471
Re: Self Nock Woodies Build
« Reply #13 on: March 22, 2021, 06:21:43 PM »
Quote from: Terry Green on March 22, 2021, 06:11:07 PM
People have no idea what a wealth of information Rob is.  Take this and the fact that he runs the guts of TG is a miss to so many.... PAY ATTENTION!

I couldn’t agree more with what Terry said.   Rob has been a treasure trove of knowledge to me  :campfire:
Logged
TGMM Family of the Bow

"The bravest are surely those who have the clearest vision of what is before them, glory and danger alike, and yet notwithstanding, go out to meet it." - Thucydides

Offline Lucas K

  • Trad Bowhunter
  • **
  • Posts: 631
Re: Self Nock Woodies Build
« Reply #14 on: March 23, 2021, 08:03:39 AM »
Very nice, thanks for the build.
Logged
Lucas Kent

Offline Jon Stewart

  • Trad Bowhunter
  • **
  • Posts: 2567
Re: Self Nock Woodies Build
« Reply #15 on: March 23, 2021, 08:07:12 AM »
Been using the original Nifty Nocker for years.  I like to use black walnut inserts for strength and color contrast. I also foot the point end when I use stone points.
 Would post photo's, but not easy for me to do.
Logged

Online Roy from Pa

  • Administrator
  • Trad Bowhunter
  • ****
  • Posts: 20685
Re: Self Nock Woodies Build
« Reply #16 on: March 23, 2021, 08:26:20 AM »
Jon if you can, email them to me I will post the photos for you.

[email protected]
Logged

Offline Will Telluteyrd

  • Trad Bowhunter
  • **
  • Posts: 52
Re: Self Nock Woodies Build
« Reply #17 on: March 23, 2021, 10:44:17 AM »
Those are some nice arrows. I use a Dremil to cut in self nocks and wrap with Sinew on my Cedars. Worked for me so far.
Logged

Offline bow loving man

  • Trad Bowhunter
  • **
  • Posts: 962
Re: Self Nock Woodies Build
« Reply #18 on: March 23, 2021, 11:08:37 AM »
Nice work as always Rob! Thanks for sharing
Logged
"...on earth as it is in heaven..."

Online BAK

  • Contributing Member
  • Trad Bowhunter
  • ****
  • Posts: 1777
Re: Self Nock Woodies Build
« Reply #19 on: March 23, 2021, 11:38:43 AM »
I had one of those first editions.  Made a few dozen with it but never fell in love with it.  Last year I made a wooden jig that I could mount the arrow shaft into and slide it across my table saw.   What an improvement.  The slots are cut perfect and I could do a dozen in about 10 minutes.  I have since gotten rid of the nifty nocker.   :coffee:

« Last Edit: March 23, 2021, 02:30:16 PM by BAK »
Logged
"May your blood trails be short and your drags all down hill."
Pages: [1] 2   Go Up
« previous next »

Users currently browsing this topic:

0 Members and 1 Guest are viewing this topic.
 

Contact Us | Trad Gang.com © | User Agreement

Copyright 2003 thru 2024 ~ Trad Gang.com ©