Author Topic: 2022 Bow Swap Progress Thread - Finished (Read 30523 times)

Noah70 · « **Reply #260 on:** April 10, 2022, 04:52:54 PM »

Beautiful lines and workmanship on that Kenny! Love the shape on the grip.

Roy from Pa · « **Reply #261 on:** April 10, 2022, 05:50:42 PM »

Very nice Kenny

Mad Max · « **Reply #262 on:** April 10, 2022, 05:54:32 PM »

Nice Bowssssss guy's

kennym · « **Reply #263 on:** April 10, 2022, 06:03:50 PM »

That’s my fave grip, I shoot it better than any , Hope my poor victim can shoot it too ! Everybody likes a bit different grip.

PV · « **Reply #264 on:** April 11, 2022, 08:05:47 AM »

Looking real nice Kenny!!
Nice save on the extra slice!

EvilDogBeast · « **Reply #265 on:** April 11, 2022, 09:01:46 PM »

New additions! Bocote, bird's eye maple, and katalox.

katalyzt · « **Reply #266 on:** April 11, 2022, 09:53:21 PM »

Quote from: EvilDogBeast on April 09, 2022, 01:08:11 AM

They are pistachio. Picked them up from Kevin Connor over at Wood From the West. Pistachio orchards cut down unproductive trees and graft new saplings onto those rootstocks, which gives them those weird, sharp demarcation lines. The orchards were using those cut trees for firewood so Kevin grabs as much as he can and cuts into bow veneers among other things. This wood, in my opinion, is so impressive that I use it almost exclusively.

I've also received some excellent woods from Kevin over there at Wood From the West and the pistachio is right up there as my fav. In fact it's what I'm using in my current build. 10/10 would recommend

EvilDogBeast · « **Reply #267 on:** April 12, 2022, 01:04:38 AM »

Did the thing!

Crooked Stic · « **Reply #268 on:** April 12, 2022, 07:03:11 AM »

That a lot of clamps sooo it oughta work

EvilDogBeast · « **Reply #269 on:** April 12, 2022, 08:43:50 AM »

I get paranoid about even pressure and flatness when the pieces are long like that. The bocote is also 3/8" so I wasn't taking any chances!

Crooked Stic · « **Reply #270 on:** April 12, 2022, 08:37:16 PM »

I have a piece of 7/16 s angle iron 3 in. Wide and a flat piece to go on top and C clamp the riser pieces. And I do well them for line up in a part that is later cut off.

EvilDogBeast · « **Reply #271 on:** April 12, 2022, 10:25:40 PM »

Turned out well I think. Opinions welcome, tell me if it sucks now before it's glued into a bow!

mmattockx · « **Reply #272 on:** April 12, 2022, 11:28:16 PM »

Quote from: EvilDogBeast on April 12, 2022, 08:43:50 AM

I get paranoid about even pressure and flatness when the pieces are long like that. The bocote is also 3/8" so I wasn't taking any chances!

If you want even pressure do like Stic says and use a straight block on top, then apply clamping force to the block.

Mark

kennym · « **Reply #273 on:** April 13, 2022, 12:16:10 PM »

Fixin to get movin ...

By the way, my poor victim, end comes outta box and slide the bow out the end. Unless you wanna use a wrecking bar and pull nails...

Screws are heavier and with shipping cost, I just couldn't use em on whole box

...

4 point · « **Reply #274 on:** April 13, 2022, 03:42:51 PM »

They’re gonna have to work to destroy that one in shipping Kenny

wood carver 2 · « **Reply #275 on:** April 13, 2022, 04:04:05 PM »

Quote from: EvilDogBeast on April 12, 2022, 10:25:40 PM

Turned out well I think. Opinions welcome, tell me if it sucks now before it's glued into a bow!

Looks good to me…
Dave.

kennym · « **Reply #276 on:** April 13, 2022, 05:23:02 PM »

I figure if I had no proof of selling it or the worth of it, or getting paid for it, there wouldn't be a chance in hell of getting an insurance claim done on it when they run over it!!

Crooked Stic · « **Reply #277 on:** April 13, 2022, 07:29:47 PM »

So it's on its way to victim ??

kennym · « **Reply #278 on:** April 13, 2022, 07:53:55 PM »

Shipping label is on it but not in mail yet. Gotta read the rules again before I ship...

Crooked Stic · « **Reply #279 on:** April 13, 2022, 08:05:58 PM »

PFFT !

News:

Author Topic: 2022 Bow Swap Progress Thread - Finished (Read 30523 times)

Users currently browsing this topic: