how can I keep nocks from blowing out of carbon shafts when stumping?

[68_super_k]

Hey guys I'm a newbie to this site.  Quick question... has anyone found a good way to keep nocks from blowing out of carbon shafts when stumping?  I can't seem to keep them in.  The only solution I've found is to keep a drywall screw and some spare nocks with me.  I tried wrapping a serve around the top of the shaft at the nock and using epoxy over the serve but that just made the nock snap and stay flush with the shaft...Any suggestions???

[lpcjon2]

Are they completely popping out on impact of the shaft? or are they breaking from hitting trees,and limbs? or are they getting stuck on the string and breaking upon release? are they to tight on the string?

[buckster]

Foot them with an inch of aluminum shafting held up place with JB weld, you will have some really tough arrows & less breakage.

[lpcjon2]

If you use a 22 cal bore brush and clean the inside of the shaft(at the nock end) and mark the shaft with a pencil to align the nock, you could as a last resort use a little CYA or epoxy to hold them in.
  I know Easton makes nocks with a longer insert part.

[don_h]

Aluminum footing works as posted above. Gorilla glue works well for attaching footing also.

[Bowsey Wails]

QUESTION: You are footing the nock end of the arrow?

[mcgroundstalker]

Carbon Shafting is cool but weak on both ends... Some fellas (like me) foot both front and back with about one inch aluminum for stumping and small game arrows... Sometimes an arrow wrap is enough to hold it in place... Most of the time J.B. Weld works good...

As for nocks popin' out...        That would not be a safe thing. Remember to flex and check your carbon arrow after each shot! Just pick the soft rocks.    :rolleyes:  

Best Of Luck!

... mike ...

[Trumpkin the Dwarf]

I want my nocks to pop out if the blow is big...that keeps the shaft intact. I never glue the nocks in, I just carry extras with me. You could always shoot softer stumps though...

[Bowsey Wails]

Thanks for sharing that, Mike. I had no idea.
Tim

[tarponnut]

The Gold Tip nocks are longer but do pop out once in awhile(especially if I have weight tubes in them)I use a drop of Super Glue.
I shot at a squirrele once and the nock shot back(I hit the tree) and almost took my eye out, I even have it on video. I've been gluing them in ever since.

[huntmaster70]

try plastic kitchen wrap over the end of the nock before you push in then trim excess.It makes them tighter & helps with "blowouts" but will still allow them to come out when needed.

Always carry some extras. A little clear nail polish or thin glue on the nock will keep them in place for all except the hardest hits.

[Bill Carlsen]

If you are using weight tubes your only recourse is gluing them. I rarely have this problem with the Beman MFX or Axis shafts. The nocks on those babies are pretty tight.

[Pat B]

Use wood with self nocks! d;^)

[onewhohasfun]

After a nock blowout inspect your shaft there. It may have a hairline crack. That's why we foot both ends. I just use a 3/8" long footing on the nock end.

[rraming]

I know how you can keep the nocks in - miss the stump  

[FerretWYO]

Teflon tape works pretty good for me.

[Jeff Strubberg]

Just glue the nock in and be done with it.

I use Goat Tuff, but any of the cysnocrylate glues will get the job done.

[68_super_k]

thanks guys.  My shafts aren't cracked at all so that's not my problem.  I'll probably just go for some glue and see what happens.  I appreciate all the great tips.

[AWPForester]

If you glue the nocks they are going to break and leave the insert part stuck in the arrow.  I know because I got fed up and let common sense lose to stupid, and did it.  Had to cut them after breaking them all off in there.

I like plumber's tape around the nock insert and push it in.  What is causing it is the nock is getting launched back out of the end when hard contact is made.  Make it tighter and problem is fixed. God Bless