Author Topic: 6'7" archer needs help (Read 945 times)

droptine59 · « **on:** August 07, 2007, 03:59:00 PM »

I got a 6' 7" buddy who is shooting a Northern Mist longbow 68" x 60# pull. He draws 35 inches.
He has been shooting 2515 aluminums and they fly lik crap. Any suggestions to get his spine correct for this length? Should he switch to Carbon? Heavy woods? or stay with aluminums? I suggested heavy woods such as Douglas Fir.

Joe Clark · « **Reply #1 on:** August 07, 2007, 04:17:00 PM »

How does that work? If he is drawing 35" than wouldn't a full length shaft of 31" be to short for him to draw and shoot?

Big Dave · « **Reply #2 on:** August 07, 2007, 04:18:00 PM »

I agrre with you on the woods in 23/64 if you can find a supply long enough. My 2 cents

Grant Young · « **Reply #3 on:** August 07, 2007, 04:26:00 PM »

Rich, You might want to contact Easton for suggestions. Back in the late 70s and early 80s several pro atheletes were featured in some archery ads; I believe Larry Byrd was one but I can't be sure. At that length he might try a 2419 but its going to be a little soft at those lengths though the additional weight might help a little. Have him check with Whispering Wind if wood is the way he wants to go. I understand they have been very accomodating to guys looking for "special" spines and weights. Grant

Shakes.602 · « **Reply #4 on:** August 07, 2007, 04:36:00 PM »

HOKIE SMOKES!

Do they have a Big & Tall Archery Shop anywhere close to where your Friend Lives?? He may have to Cut Down Some Fence Posts to Make his Arrows!!

BigRonHuntAlot · « **Reply #5 on:** August 07, 2007, 04:52:00 PM »

35 inches... With that kinda of power stroke he should be able to shoot through an engine block. LOL Good Luck on finding some shafts.

dachba · « **Reply #6 on:** August 07, 2007, 05:01:00 PM »

If I needed a 35 inch arrow, I would use one of the stronger spined carbons and join a section of one to another to make a single long arrow. Just find some aluminum rod in the right diameter and make an insert two to three inches long then epoxy the pieces together. It might work. The same thing might work with aluminum arrows. It would seem that to keep an arrow that long from being whippy, you would need a stronger spine than the draw weight might suggest.

Dave in Ft. Collins, CO

vermonster13 · « **Reply #7 on:** August 07, 2007, 05:11:00 PM »

Rebar comes to mind at that length.

ChuckC · « **Reply #8 on:** August 07, 2007, 05:12:00 PM »

Many of the 36" ramin shafts(3/8") were real heavyweights...over 100 pound spine. Maybe you can work with some of them.
ChuckC

bbassi · « **Reply #9 on:** August 07, 2007, 05:23:00 PM »

If you bring him to Denton next year I AIN'T pulling his arrows!

bjk · « **Reply #10 on:** August 07, 2007, 05:28:00 PM »

Hey Rich,

I don't think you have any modern material options, but with wood you do. You could get someone who runs the shafts to keep them longer (Troy used to do this, the new guy might also). Or you could take regular full length woods and use the reparrow idea (used to fix, but in this case to add 4 inches or more).

Bring him to Denton, I'd like to see a real life giant.

Chortdraw · « **Reply #11 on:** August 07, 2007, 05:45:00 PM »

Long footed shafts would give some stiffness

Biggie Hoffman · « **Reply #12 on:** August 07, 2007, 05:48:00 PM »

I draw 32" and can't find woodies anymore. With a 65# bow I need 90-95# shafts and then they have to be footed. I doubt you'll find woodies stiff enough.

Tom A · « **Reply #13 on:** August 07, 2007, 05:49:00 PM »

Id be looking for a bow with an overdraw shelf.

C2@TheLibrary · « **Reply #14 on:** August 07, 2007, 06:10:00 PM »

I have a friend that draw 34" full length 2419s work for him out of a bow that at his draw length is 68#. He also has a recurve that pulls 107# at his drawlength and a Big 5 Longbow that pulls 127# at his drawlength and with those bows he shoots 2440s with a 200 grain head those arrows weigh 1750 grains and they still are pushing 190 fps. I watched one shoot through 6 1 1/2" think sheets of marine plywood and the fender of a 1974 Nova it stopped against the engine block of the Nova and flatten out the fieldpoint.2440s are very hard to find though.
I know Rouge River Archery makes shafts over 100# spine and you could use the Reparrow shaft repair add ons to make 36" arrows.

Linc · « **Reply #15 on:** August 07, 2007, 07:00:00 PM »

Ramin shafts can spine upwards of 100+ and they come in 36" lengths.

WESTBROOK · « **Reply #16 on:** August 07, 2007, 07:10:00 PM »

I think he needs more bend in his elbow!

Eric

ckruse · « **Reply #17 on:** August 07, 2007, 07:34:00 PM »

I'm going to be working on this. I think if we get this guy set up right, victory against the Orcs is ours! May good always triumph over evil!

CKruse

bmfer · « **Reply #18 on:** August 07, 2007, 09:34:00 PM »

Broomsticks and Snuffers!! I could tig weld an adapter to a thimble, jam it on there, pound a nail through it all and bend it over!!

sagebrush · « **Reply #19 on:** August 07, 2007, 11:40:00 PM »

He needs to find someone that has a doweling machine and that can make the shafts longer and bigger around. Or get a saw and a drill and a router and make your own. Course' he would have to have a very good spine tester that worked up to 150#s. But it sounds like fun to me.


LEFT HAND BOWS CLASSIFIEDS	TRAD GANG CLASSIFIEDS ACCESS	RIGHT HAND BOWS CLASSIFIEDS

News:

Author Topic: 6'7" archer needs help (Read 945 times)

Users currently browsing this topic: